EX9_LCD1602

SAMSUNG S3C2440开发文档大全---(。)

51单片机编程器制作资料。内有pcb，原理图，物料清单，hex文件。自制成功(51 Microcontroller Programmer production of information. There pcb, schematics, BOM, hex file. Self-made success)

NRF24L01Information Program(NRF24L01 Information Program)

CH341 上位机软件，支持I2C UART等 接口(CH341 host computer software, support I2C, UART and other interfaces)

AB PLC通信sdk以及CIP协议规范(AB PLC communication SDK and CIP protocol specification )

led fleshing in use 8051

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

这是一个能生成C程序代码的软件，用来编写液晶屏上的内容非常方便。(This is a program that generates C source software, used to write the contents on the LCD screen is very convenient.)

C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC ( Data Acquisition example for C8051F060 Description: This example illustrates the use of ADC1 and the DMA to acquire and store data. It is intended for use with the C8051F060 target board in the development kit. // This code measures a signal at the AIN0 input with the 16-bit SAR ADC0. // The data is sampled at a rate of 100kHz. ADC output data is transferred to XDATA memory space using the DMA. // // With the EMIF configured for off-chip XRAM access (on the upper ports), this code moves the ADC data to the C8051F060TB target boards s SRAM device. // Once data acquisition is complete, the code then prompts the user to press the P3.7 // button on the target board when ready to receive the data via the UART0 serial port. The TB features an RS-232 transceiver and connector, so the data can be transferred // to a PC via its serial port. // The code is set to acquire up to 32768 samples (for 64kbytes of data). The SRAM device - can accommodate up to 128kbytes, )