DLT645-1997

程序代码说明 P0401：用Prewitt算子检测图像的边缘 P0402：用不同σ值的LoG算子检测图像的边缘 P0403：用Canny算子检测图像的边缘 P0404：图像的阈值分割 P0405：用水线阈值法分割图像 P0406：对矩阵进行四叉树分解 P0407：将图像分为文字和非文字的两个类别 P0408：形态学梯度检测二值图像的边缘 P0409：形态学实例——从PCB图像中删除所有电流线，仅保留芯片对象(code P0401 Note : Prewitt operator to detect the edges in the image P0402 : different values of Getting operator to detect the edges in the image P0403 : Canny operator to detect the edges in the image P0404 : image thresholding segmentation P0405 : water line threshold method image segmentation P0406 : matrix Quadtree P0407 : images into text and non-text of the two categories P0408 : morphological gradient detection Binary Image Edge P0409 : morphology example-- Images from the PCB to remove all current lines, retaining only chip targets)

ISIS实现仿真MSP430单片机开发，有MSP430SRVPAK++7.5补丁和测试程序仿真图(ISIS achieve simulation MSP430 development, and testing procedures have MSP430SRVPAK++7.5 patch simulation diagram)

红外通信装置 HSDL-7001PDF资料(Infrared communication device HSDL- 7001 PDF data )

光电编码器，是一种通过光电转换将输出轴上的机械几何位移量转换成脉冲或数字量的传感器。 这是目前应用最多的传感器，光电编码器是由光栅盘和光电检测装置组成。光栅盘是在一定直径的圆板上等分地开通若干个长方形孔。由于光电码盘与电动机同轴，电动机旋转时，光栅盘与电动机同速旋转，经发光二极管等电子元件组成的检测装置检测输出若干脉冲信号(Photoelectric encoder, a photoelectric conversion to the output shaft of the mechanical geometry of displacement into a pulse or digital sensors. This is currently the most widely used sensors, optical encoder is determined by the grating disk and photoelectric detection device component. Grating disc is a circular plate in such a diameter of several rectangular holes partially opened. Because coaxial photoelectric encoder and the motor, the motor rotates, the grating disk rotates with the same speed motor, the light-emitting diodes and other electronic components of the detection device detects certain pulse signal output)

基于单片机的人流量统计系统的设计与仿真。(Design and Simulation of human traffic statistics system based on single chip microcomputer.)

单片机与FPGA的串口通信 单片机与FPGA的串口通信(MCU and FPGA-MCU and FPGA serial communication Serial communication)

51单片机新型按键扫描，不用10ms延时消抖，实时性大大提高。每个按键有长按短按功能，采用结构体对象化编程，增加按键极度方便。(The new key scan does not use 10ms delay to eliminate jitter, and the real-time performance is greatly improved. Each button has a long press, a short press function, the use of structured object programming, increasing the key, extremely convenient.)

一个通过USB->UART读取C8051F060的程序，实现曲线分析、放大、报表等，采用多线程。 驱动从www.silabs.com下载，要用NI的UI控件。完整版。(a USB-)

实用CAN与上位机通讯例程，适用于基于CAN总线的自动系统参考。(Practical CAN and PC communication routines for automated reference system based on CAN bus.)

无线传感器网络中基于PSO的分簇路由算法(Wireless sensor networks based on PSO clustering routing algorithm)