MFiles

cleaks fadeing model

基于多相催化反应动力学的特点和基本原理,提出多相催化反应动力学方程的一般形式,并介绍了用Matlab语言设计确定多相催化反应动力学方程参数的通用程序.处理时先对实验测定不同时刻对应的反应速率v0和浓度C(或压力P),利用无约束最优化计算方法求出多相催化反应动力学方程参数.文中以镍硅藻土催化苯加氢合成环己烷的实验数据为例进行验证,结果表明,利用所编程序确定的动力学方程和理论值及文献值很好吻合.(Based on the characteristics and dynamics of the basic principles of heterogeneous catalysis, heterogeneous catalysis proposed general form of kinetic equation and introduces heterogeneous catalytic reaction kinetics equation to determine the parameters used in Matlab language design common procedures when handling the first experimental measured at different times corresponding to the concentration of the reaction rate v0 and C (or pressure P), the use of unconstrained optimization calculations obtained heterogeneous catalytic reaction kinetics equation parameters. text nickel diatomaceous earth catalytic hydrogenation of benzene cyclohexane an example to validate the experimental data, the results show that the equations and theoretical value and dynamics literature values ​ ​ determined using the programmed good match.)

This paper presents an analytical study on different clustering techniques used for image segmentation

采用积分分离 PID控制算法将塔顶轻组分含量Y控制在0.99 2.采用继电法整定PID参数 3.整定效果验证：当被控过程参数时变时，如滞后时间由4→8，开环增益由3.4→6时, 讨论PID控制的响应速度及鲁棒性问题，考察当系统参数发生改变时，上述PID参数是否选取合适。 (Using integral separation PID control algorithm to control the top of the tower light component content Y 0.99 2. Verify tuning PID parameters of the relay method. Tuning effect: the change When accused of process parameters, such as the lag time from 4 → 8 open loop gain from 3.4 → 6 discussed PID control of the response speed and robustness issues investigated when the system parameters are changed, the PID parameters is selected for suitable.)

gabor变换是非平稳信号处理的有效方法之一，在时频平面内可获得最佳划分(gabor transform one of the effective methods of non-stationary signal processing, get the best in the division of the frequency plane)

汽车仿真关于汽车经济性的源代码，很不错的资料。(car )

MATLAB环境下小波变换的英文书籍,介绍了MATLAB编程、滤波器、正弦曲线、傅里叶变换、Z变换、小波变换并介绍了几个应用例子(English contents: 1.Introduction 2.MATLAB 3.Filters 4.Sinusoids 5.Sampling 6.The Fourier Transform 7.The Number e 8. The z-Transform 9.The Wavelet Transform 10.Applications )

最大似然估计算法Matlab实现，不容易啊！！！！！！！！！！(Maximum likelihood estimate，not so esay！！！！！！！！！！)

利用目前风力机叶片设计普遍采用的优化设计方法Wilson设计A-法，通过MATLAB编程，开发了小型叶片气动设计的应用程序，并利用该程序设计了一台3kW小型水平轴风力机叶片。采{用MATLAB和ANSYS共同建立了风力机叶片三维有限元参数模型，MATLAB编制的建模程序提高了{初期设计效率，缩短了ANSYS分析前处理时间。在此基础上进行了叶片固有振动特性计算，分析了叶《片的振动特性及其与结构参数之间的关系，分析方法和结果对风电叶片的结构设计和动力分析有一定；的参考价值。(Advantage of the current design of wind turbine blades commonly used in optimal design method Wilson designed the A-Law, MATLAB programming, developed a small blade aerodynamic design application and use of the program designed a 3kW small horizontal axis wind turbine blades. Mining {using MATLAB and ANSYS common parameter model of wind turbine blades dimensional finite element modeling program MATLAB prepared the {initial design efficiency, shortening the ANSYS analysis of the pre-treatment time. On this basis, the natural vibration characteristics of leaves, the relationship between leaf on vibration characteristics and structural parameters, analytical methods and the results of analysis has some structural design of wind turbine blades and power reference value.)

MIMO系统中QPSK信号的MMSE检测算法程序，用于衰落信道环境。(MMSE detection for QPSK signals in MIMO systems.)