armyants

用matlab语言来实现DFP算法，源码中有例子(Matlab language used to achieve the DFP algorithm, there are examples of source)

对图像进行逐点计算，并且取最大值和最小值的差值作为该点新的灰度值。 在区别边缘点和非边缘点时，首先确定一个阈值T，若图像中像素点的新 值大于该门限值，则可以初步确定为边缘点，小于T的新值被判断为非边缘点.(Image point by point basis, and taking the maximum and minimum points of difference as the new gray value. Edge in the difference between point and non-edge point, first determine a threshold T, if the image of the new pixel value is greater than the threshold, you can initially identified as the edge point, the new value is less than T have been judged as non-edge point.)

simpson method used in matlab

本程序是实现电力系统的故障计算程序，故障后会对导纳矩阵进行修正，很好的进行了仿真(This program is a power system fault calculation program, fault admittance matrix will be revised, a good simulation)

根据对真空蒸发镀膜的分析，在40×40的范围内分别蒸 发：1000、5000、10000、20000、30000个粒子。  利用2维数组记录每个点的粒子数。  初始粒的横纵坐标为0～40的均匀分布。  能量为（15，3）的正态分布。  在基体表面自由行走时损失1的能量。  若该点有粒子，即与其他粒子相遇时损失3的能量。  由低处向高处扩散，每扩散一层，损失4的能量，由高处 向低处扩散，损失3的能量。  当粒子的能量小于等于0时停留下来，该点的粒子数加1。  临界核的尺寸为10个粒子。  根据每个点粒子个数的不同，以不同的灰度显示这些点。 点越亮，则表示该点的膜越厚。  以图形方式显示粒子初始能量的正态分布情况(Based on the analysis of the vacuum evaporation coating, respectively, in the range of from 4040 evaporated: 1000,5000,10000,20000,30000 particles.  each point using 2-dimensional array to record the number of particles. The  initial grains transverse and longitudinal coordinates of a uniform distribution of 0 to 40. The  energy as a normal distribution (15,3).  1 energy losses in the substrate surface to walk.  point particles that 3 energy loss in the encounter with the other particles.  by the lower diffusion tops every diffusion layer, a loss of 4 energy diffusion from high to low, the energy loss of 3.  When the energy of the particles is less than or equal to 0:00 stay down, add 1 to the number of particles that point.  critical nucleus size of 10 particles.  these points, depending on the number of particles of each point is displayed in a different shade. Point, the brighter, the thicker the point of the fi)

用matlab做的有关边缘检测的一个代码，该代码可以进行多种的边缘检测(Using matlab to do the edge detection of a code that can be a variety of edge detection of)

说明：  用MATLAB实现对一语音信号用不同小波进行分解，提取各层的高低频系数，画出各系数波形，并重构。(MATLAB voice signal to a different wavelet decomposition, from the high levels of low-frequency coefficients. he painted the waveform coefficients, and Reconstruction.)

matlab算最短路径的算法，很好用大家可以试一试(Matlab operator of the shortest path algorithm, we can use a good try)

基于状态空间模型的预测控制程序，参考了钱积新的《预测控制》(Predictive control program based on state space model, refer to the Qian Jixin’ s predictive control )

plot an ellipse using matlab