-
BaslerDemo
实现balser相机连续采集及硬触发模式,也可设定AOI区域,还可修改曝光及增益等光学参数(basler continous capture and hardware trigger mode)
- 2018-03-25 20:59:02下载
- 积分:1
-
Barcode
This is Baroce module
- 2020-06-25 02:00:01下载
- 积分:1
-
PV-Controller
光伏控制器,自动充放电控制12V/10A光伏控制器(ERA-04-10-A):
额定工作电压:DC12V
最大充电电流:10A
最大放电电流:5A/路(共两路负载)
太阳能组件开路电压:25V
空载电流:<15mA
温度补偿:-20Mv/°C
工作环境温度:-25°C~+50°C
使用海拔:<5500M
控制器尺寸(mm):
光控电压(25°C):<=3.3V
过放保护电压(25°C):<10.8V
过放恢复电压(25°C):>10.8V
过充保护电压(25°C):>15.0V
过压保护电压:17.68V
过压恢复电压:14.7V
浮充电压(25°C):13.4V~13.7V
恢复正常充电电压(25°C):13.2V
结束正常充电电压(25°C):15.0V
(PV controller, automatic charge and discharge control 12V/10A PV controller (ERA-04-10-A): Rated voltage: DC12V Maximum charge current: 10A Maximum discharge current: 5A/Road (a total of two loads) Solar components of the open circuit voltage: 25V No-load current: < 15mA Temperature Compensation:-20Mv/° C Operating Temperature:-25 ° C ~+50 ° C with elevation: < 5500M Controller Size (mm): light control voltage (25 ° C): < = 3.3V over-discharge protection voltage (25 ° C): < 10.8V over-discharge recovery voltage (25 ° C):> 10.8V overcharge protection voltage (25 ° C):> 15.0V over-voltage protection Voltage: 17.68V overvoltage recovery voltage: 14.7V float voltage (25 ° C): 13.4V ~ 13.7V back to normal charging voltage (25 ° C): 13.2V end of the normal charging voltage (25 ° C): 15.0V)
- 2021-04-22 17:08:48下载
- 积分:1
-
FiveAxisNC
该程序为五轴联动程序,采用固高的板卡来控制。界面显示仿真,实时显示各个传感器的值等。(The program for the five-axis programs, using solid-high board to control. Interface display simulation, real-time display the value of each sensor and the like.)
- 2021-02-14 09:49:49下载
- 积分:1
-
DMBS
说明: 无线传感器网络中,关于定位的算法dmbs,具体算法(Wireless sensor network, the algorithm on the positioning dmbs, the specific algorithm)
- 2020-09-25 13:37:47下载
- 积分:1
-
pushboxVC6
说明: c语言实现推箱子的程序,很有意思~可以实现基本功能~(c language Sokoban program, very interesting ~ ~ can realize the basic functions)
- 2010-04-05 21:02:38下载
- 积分:1
-
第2章
哈尔滨工业大学,visual basic,编程课件,第2章(Harbin University of Technology, Visual Basic, Programming Courseware, Chapter 1)
- 2020-06-24 14:20:01下载
- 积分:1
-
overset
基于fluent模拟实物在流体中运动情况(Simulation of physical movement in fluid based on fluent)
- 2018-08-28 10:02:40下载
- 积分:1
-
5290
精品小程序,可供大家参考zszszszs(study program zszszszszszs)
- 2018-06-08 10:52:08下载
- 积分:1
-
VIEWNC
这是用VB写的数控G代码读取,编译,并显示。给做数控系统的朋友做参考。(It is written in VB CNC G-code read, compile, and displayed. CNC system to make a friend for reference.)
- 2013-08-28 11:02:26下载
- 积分:1