AVO

水文管理信息系统，整理水文数据，绘制水文图(Hydrological management information system, collation of hydrological data, hydrological Figure Drawing)

NET Core+EF Core实例,自己使用了,很好,没有问题(NET Core+ EF Core instance, oneself use, is very good, no problem)

visual basic program penerimaan mahasiswa baru

基于长期负荷预测的线性规划燃机出力能量优化控制(Long-term load forecasting based on linear programming optimization of gas turbine power output control)

光伏控制器，自动充放电控制12V/10A光伏控制器（ERA-04-10-A）： 额定工作电压：DC12V 最大充电电流：10A 最大放电电流：5A/路（共两路负载） 太阳能组件开路电压：25V 空载电流：<15mA 温度补偿：-20Mv/°C 工作环境温度：-25°C～+50°C 使用海拔：<5500M 控制器尺寸（mm）: 光控电压（25°C）：<=3.3V 过放保护电压（25°C）：<10.8V 过放恢复电压（25°C）：>10.8V 过充保护电压（25°C）：>15.0V 过压保护电压：17.68V 过压恢复电压：14.7V 浮充电压（25°C）：13.4V～13.7V 恢复正常充电电压（25°C）：13.2V 结束正常充电电压（25°C）：15.0V (PV controller, automatic charge and discharge control 12V/10A PV controller (ERA-04-10-A): Rated voltage: DC12V Maximum charge current: 10A Maximum discharge current: 5A/Road (a total of two loads) Solar components of the open circuit voltage: 25V No-load current: < 15mA Temperature Compensation:-20Mv/° C Operating Temperature:-25 ° C ~+50 ° C with elevation: < 5500M Controller Size (mm): light control voltage (25 ° C): < = 3.3V over-discharge protection voltage (25 ° C): < 10.8V over-discharge recovery voltage (25 ° C):> 10.8V overcharge protection voltage (25 ° C):> 15.0V over-voltage protection Voltage: 17.68V overvoltage recovery voltage: 14.7V float voltage (25 ° C): 13.4V ~ 13.7V back to normal charging voltage (25 ° C): 13.2V end of the normal charging voltage (25 ° C): 15.0V)

计算多跨连续梁内力并绘制弯矩图，计算书度快且准确(inner force calculating)

说明：  这是将波动方程分解为上行波下行波的源程序 把两个源代码放在一起，运行即可了！(This is the wave equation will be decomposed into up-going wave downlink wave source source code of the two together, you can run the!)

该程序实现重力勘探中的布格重力场校正，程序包括，地形校正，中间层校正，高度校正，纬度校正，程序较为复杂，但注释清楚利用理解。(The programis about of the Bouguer gravity field correction, including terrain correction in gravity exploration, the middle layer height correction, correction, correction of latitude, the program is relatively complex, but notes with clear understanding.)

测绘程序2013，适用于各种测绘数据处理，内附程序模块及操作说明，使用方便。(2013 mapping program, mapping data can be used in a variety of computing, has attached the software interface and operating instructions.)

说明：  VC++ 6.0调用omron Compolet V2控件与PLC通信 示例(VC++ 6.0 call omron Compolet V2 control)