在PIC16C55上实现时钟功能.

医疗电子,血氧浓度测量模块原程序,采用430 单片机.-medical electronics, oxygen concentration measurement module program, using 430 SCM.

基于8051单片机的遥控电风扇的红外发射源程序-8051-based remote control of the infrared emission source fans

由AT98C51单片机硬件电路,用C51编写的红外线解码程序. -AT98C51 single-chip hardware circuit by using C51 decoding procedures for the preparation of infra-red.

arm-led汇编程序，适合初学者学习最基本的 arm汇编指令-arm-led compilation of procedures, suitable for beginners to learn basic arm compilation directives

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

该压缩包包含了型号为VGG12864的OLED液晶的单片机驱动程序，液晶使用说明以及字模生成软件。该工程对应单片机型号为Motorola的MC68HC908GZ32，只需在头文件中对I/O简单配置后即可使用与其他任何型号的单片机-The archive contains the model VGG12864 of OLED LCD driver, microcontroller, LCD instructions, as well as matrix generation software. The project SCM model corresponds to Motorola" s MC68HC908GZ32, just in the header file of the I/O simple configuration can be used with any other type of MCU

用Keil uVision2编写得批量in传输程序，实现简单得数据采集，我看了觉得很有用-with Keil uVision2 prepared in bulk in transmission process, in simple data collection, I saw very useful

凌阳公司61板子的电路图，供大家一起学习-Sunplus Company 61 of the circuit board for everyone to learn

Keil写的320*240的液晶显示程序。很有参考意义。-Keil written 320* 240 LCD display program. Very useful.

HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1、A2 所接地址需一一对应。一个为芯片写保护脚WP，WP 脚接低电平时，芯片可进行读写操作；WP 脚接高时，芯片只可进行读，不可进行写。 另外两个管脚为电源脚VCC，VSS。 用单片机对HT24 系列的EEPROM 进行控制时，HT24 系列的EEPROM 的外部管脚VCC、VSS、WP、A0、A1、A2 根据需要，对应接上，SDA、SCL 接到单片机控制脚上。-HT24 Series EEPROM total of 8 pins, three pins for the chip address A0, A1, A2, in the microcontroller to operate it, from SDA input A0, A1, A2, and chip external data A0, A1, A2 of the Then one correspondence address must be in. One for the chip, write-protect pin WP, WP feet then low, the chip can be read and write operations WP pin is high then, the chip can only be read, not write. The other two pins for the power pin VCC, VSS. With the microcontroller on the HT24 Series EEPROM control when, HT24 Series EEPROM external pin VCC, VSS, WP, A0, A1, A2 according to the needs of the corresponding connected, SDA, SCL receives SCM control feet .