基于51单片机的电压调节系统，可以实时显示电压值。用keil开发环境，protuse仿真。...

8051F040的can总线底层驱动开发程序，可以移植到项目中。-The bottom of the can bus 8051F040-driven development process, can be transferred to the project.

此代码可用来控制数码管及LED的显示，对初学单片机的人很有帮助-This code can be used to control and LED digital tube display, and the people very helpful beginner Singlechip

基于8051的高精度的秒表汇编程序，从0到60秒，有复位，暂停，累计功能。附加protues连接图-Based on the 8051 compilation of high-precision stopwatch program, from 0 to 60 seconds, a reset, pause, the cumulative function. Additional protues connection diagram

基于FREESCALE单片机9S08DZ60的CAN的应用层源代码.开发环境为CODEWARRIOR FOR HC08-Based on Freescale

c8051f340的usb程序，经过自己的从头开始写到通讯完好。可以直接使用-c8051f340 the usb procedures, through their written communication in good condition to start from scratch. Direct access to

俄罗斯方块程序 ,本压缩包里面含有原理图和远程序(Proteus),-Russian box procedure, the compressed packet inside contains schematic and far from the procedure (Proteus),

这篇实验报告是关于单片机多路数据采集的，本实验由2大部分组成：1、为用EPOROM构成的心电信号发生器；2、为多路信号的微机采集与显示；第一部分实验主要研究可编程序存储器EPROM的非计算机应用。把存储在EPROM中的数字心电信号读出并通过D/A转换为模拟信号显示在示波器屏幕上。 第二部分实验的目的是研究一个数据采集系统，该系统利用ECD-51型单片机为中心，由D/A芯片等将各种低频信号以及由EPROM产生的模拟人体心电信号变换成离散的数字信号存入微机内存，以待进行数据处理和分析，然后再通过D/A转换将其还原成模拟信号显示在示波器的屏幕上。 -This experimental report on the multi-SCM data acquisition, the experiment by the two major components : 1. EPOROM pose for the use of the ECG signal generator; 2, multi-path signals in the computer acquisition and display; the first major study of experimental programmable EPROM memory in non-computer applications. Stored in the EPROM of ECG read out by D/A conversion of analog signals displayed on the oscilloscope screen on. Part II The purpose of this experiment is to study a data acquisition system, which uses ECD-51 microprocessor as the center, from the D/A chips, and other various low-frequency signal from EPROM and the simulation of human ECG transform into several discrete signal words into computer mem

这是LCD1602与msp430之间的通信,其实可以直接从51移植过来,但是一定要在硬件加上拉电阻,要不然是不通不过的,我说的是你用的是5V的LCD-This is the LCD1602 and communication between the MSP430 can in fact be a direct transplant from the 51, but must be coupled with pull-up resistor in the hardware, otherwise it is unreasonable, however, I say is that you use the LCD is 5V

是实验操作过程的详细讲解，有源程序即控制：转，停；正，反；快，慢；-experimental operation is the detailed talks, a source that is control : turn and stop; Now, anti-; Fast, slow;