AVR单片机应用系统开发典型实例_3

4*4键盘程序，来自msp430系列单片机-4* 4 keyboard procedures, from MCU Controller Series

12864LCD(带汉字库)显示遥控键值读取器 * * LCD型号：TS12864A-3（带汉字库）或兼容型号 控制器ST7920 * * MCU:AT89S52 ,晶体频率：11.0592MHz * * P0口为128*64LCD的数据 D0-D7 * * K17键按下，继电器吸合。K19键按下，继电器关闭 * * 显示程序在中断服务程序之中-12864LCD (with汉字库) shows the remote control key reader** LCD Model: TS12864A-3 (with汉字库) or compatible controller Model ST7920** MCU: AT89S52, crystal frequency: 11.0592MHz** P0 population is 128* 64LCD data D0-D7** K17 button pressed, the relay pull-in. K19 button pressed, the relay to close** display program in the interrupt service routine of

I2C的源代码,经本人测试通过,完全没有任何错误-I2C source code, as I tested, there is no any error

一个在Proteus仿真平台上模拟串口发送9位数据的方法。-Proteus simulation of a simulation platform 9 serial port to send data.

8051单片机c语言彻底应用-8051 c thoroughly Application Language

单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。 编程使波形信号输出电路输出正弦波信号，并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10，共11个等级。 -Singlechip P1 I connect with the four buttons for the signal amplitude and frequency adjustment operation keys. Singlechip P0, P2.7, P3.6 (-WR) and DA0832, 2 months 741 (operational amplifier) to connect constitute waveform signal output circuit. Programming so that waveform signal output circuit output sine wave signal, and can be operated keys adjust the signal amplitude and frequency. Amplitude and frequency adjustment level from 0 ~ 10, a total of 11 grades.

的应用原码可以直观使用请不要将文件放在这两个目录下-Application of the original code can be intuitive to use, please do not file on these two directory

凌阳单片机的语音程序4，供学习凌阳单片机的学习者参考-Sunplus SCM four voice procedures for learning Sunplus SCM reference learners

麦迪工作室51开发板LED数码管的驱动代码-Madison Studio 51 development board LED digital tube driver code

用中断的方式控制lcd的显示，单片机仍然是h83664十六位单片机。此程序包含单片机的接口的配置以及各种写lcd的子程，使用中断来控制lcd顺序显示A－Z，当然，可以换成其他的显示内容，由于接口程序已经编好，只需要把要显示的内容改一下就可以实现其他内容的显示-With interruption control lcd display, single-chip is still 16 Singlechip h83664. This procedure includes the configuration of single-chip interface and a variety of writing a sub-lcd-way, the use of interrupt to control the order in lcd display A-Z, of course, can be replaced by other display content, as a result of interface procedures have been developed only to To display the contents of change can be achieved about the display of other content