is using a 8051+ ds12887 code procedure is a very detailed explanation can be us...

之前用C51做了，感觉不够快，有点闪，试着移过来用M8做。 -Done before the use of C51, the feeling is not quick enough, a bit flash, try to move up to do with M8.

这是一个简单的pid控制程序，用的是增量式pid控制，在智能车上使用的。-This is a simple pid control procedures, using the incremental pid control, used in the smart car.

基于51的动态内存管理-dynamic memory management

本系统采用MSC-51系列单片机ATSC51和可编程并行I/O接口芯片8255A为中心器件来设计交通灯控制器，实现了能根据实际车流量通过8051芯片的P1口设置红、绿灯燃亮时间的功能；红绿灯循环点亮，倒计时剩5秒时黄灯闪烁警示（交通灯信号通过PA口输出，显示时间直接通过8255的PC口输出至双位数码管）；车辆闯红灯报警；绿灯时间可检测车流量并可通过双位数码管显示。本系统实用性强、操作简单、扩展功能强。 -The system uses MSC-51 series single-chip ATSC51 and programmable parallel I/O interface chip 8255A-centric device designed to control traffic lights, can be achieved in accordance with the actual traffic flow through the P1 port 8051 chip set red, green fuel Liang function of time traffic light cycle, the countdown five seconds left when the yellow light flashing warning (traffic lights through the PA output signal indicates the time directly through the PC port output 8255 to double-digits) vehicle alarm闯红灯 green time traffic flow can be detected through a double-digital display. The system practical, simple and strong extensions.

AD9852的单音频产生波形程序 加载失时钟是内部设置的 -AD9852 single audio waveform procedures produce an internal clock to load default settings

spansion公司的NorFlash:s29al004d的驱动代码。16位读取方式。在东芝32位CPU：TMP92ca25上调试通过。NorFlash的驱动方式基本上相同，其它品牌的NorFlash只需略微修改程序即可。-the NorFlash : s29al004d driver code. 16 reading. The Toshiba 32 CPU : TMP92ca25 on debugging through. NorFlash driven essentially the same way that other brands NorFlash only slightly modified procedures.

使用51单片机的音乐播放程序，带有Proteus仿真-51 single-chip microcomputer use music player with Proteus simulation

At can be given its arguments in a file. You can comment out lines by preceding them with either # or - characters. This is an easy way to temporarily disable some commands. The CONTINUE-command is most useful at the end of the file. When this command is read, the file is started again from the beginning. You can use it situations where the machine is not shut down for the night and you want to run some commands every day.- At can be given its arguments in a file. You can comment out lines by preceding them with either# or- characters. This is an easy way to temporarily disable some commands. The CONTINUE-command is most useful at the end of the file. When this command is read, the file is started again from the beginning. You can use it situations where the machine is not shut down for the night and you want to run some commands every day.

IAR for AVR是ATMEL公司推荐的AVR开发环境，其代码编译效率比GCC和ICC高25 到50 ，因此深受欢迎，但其相关的资料却很少，我上传一些能快速上手的资料（包括IAR的扩展关键字，GCC AVR的代码如何移植到IAR等等）-IAR for AVR is ATMEL" s AVR recommended development environment, its code is more efficient than GCC and ICC to compile a 25 to 50 , so very popular, but very little relevant information, I would upload the information that can quickly get started (including the expansion of IAR keyword, GCC AVR code for how to migrate to IAR, etc.)

多路巡回检测，已成功调试，12887芯片制作，51单片机编程-Multi-circuit testing, debugging has been successful, the production of 12,887 chips, 51 single-chip programming