支持XMODEM,YMODEM,FAX协议的串口通信软件包的下一个：基于TAPI应用的通信应用...

C++Builde上位机测试程序-C Builde PC testing procedures

该程序用单片机来控制无线收发模块nrf905,实现数据的无线传输-the procedures used to control the microcontroller wireless transceiver module nrf905, wireless data transmission

西门子PLC步进电机控制+TD200显示示例-Siemens step moter+ TD200 Demo

用从c++编写的串口通信程序，内有详细的了解并设置串口参数的源码，并含通信原理-prepared from the use of serial communication program, with detailed understanding of serial port parameters and set up the source code, and communication with Principle

研华单通道ad采集程序-Advantech single ad Acquisition

本文详细地介绍了在Win32环境下通过调用通信API 函数以异步方式来实现PC机和MCS 51 单片机之间的通信过程给出了软硬件设计机理以及详细的通信协议说明-This article described in detail in the Win32 environment by calling the communication API function in order to realize asynchronous approach to PC and MCS 51 Singlechip give the communication process between the design of the mechanism of the hardware and software as well as detailed description of the communication protocol

uart transmitter logic

从串口读取数据，有两种方法，1、每接收一个EV_RXCHAR,就用ReadFile读一次，这样我觉得太恐怖了。2、接收到一个EV_RXCHAR后，等一定数据量的CPU周期(GetTickCount),再一次性读取缓冲区里的数据。这样做，一般情况下不会有问题，但是，如果数据很多，过了“一定数据量的CPU周期”，还没收完数据怎么办？就会少读数据了。 我用三个线程序来完成串口数据的接收，其实就是第一种方法的变种： 一个侦听EV_RXCHAR,一个对EV_RXCHAR进行分析，其实就是超时判断。如果接收到一个消息后，一段时间没收到下一个EV_RXCHAR，就认为是一个数据包的结束。这个线程就会通知数据接收线程，进行数据接收。一般同一包数据，两个字符之间的时间间隔，应该很小了吧，而两个数据包之间的间隔，应该不会太小吧！（这个地方我不清楚，猜的:( :) ）最后一个线程，是接收数据的。-read data from the serial port, there are two methods, one, each receiving a EV_RXCHAR, on the ReadFile read, I think this vote. 2, received a EV_RXCHAR after a certain volume of data, such as CPU cycles (GetTickCount), and the one-time reader, the data buffer. To do so, under normal circumstances there is no problem, but if many of the data, and after a "certain amount of data the CPU cycles," also confiscated End Data how do? Few will read the data. I used three lines to complete serial data reception, the first method is a variant : an interception EV_RXCHAR, one pair of EV_RXCHAR analys

云台开发程序，VB环境。-Haeundae development process, VB environment.

利用MSComm控件，不依赖太多硬件设备，指利用纯软件方法侦测串口通信参数设置情况-use MSComm control, do not rely on too many hardware devices that use software-only method to detect serial communication parameters settings