with C

本程序用于把串口助手所写内容通过pc发送给单片机，并且由单片机把所写内容发送到lcd上面进行显示，所用单片机为日立系列h83664十六位单片机，实验证明可以准确显示pc上面所写的内容。里面包含各个写lcd的子程-This procedure for the serial written by aides through the pc sent to the microcontroller, and written by Singlechip the above content is sent to the lcd display, single-chip microcomputer used for the Hitachi series h83664 16 microcontroller, Experiments show pc can accurately display the contents of the above written. Which contains a subset of the various write-way lcd

PCF8563T读写功能程序（原创）-PCF8563T read and write capabilities (original)

嵌入式系统已经广泛应用于各个科技领域和日常生活的每个角落，由于其本身的特性，使得我们很难发现它的存在。甚至一些从事嵌入式系统开发的科技人员也只知单片机，不知道嵌入式系统。本节从嵌入式系统的定义开始，阐述嵌入式系统的含义、特点等，以使读者加深对嵌入式系统的理解。 -Embedded systems are widely used in various fields of science and technology and everyday life in every corner, due to its own characteristics, making it very difficult for us to discover its existence. Embedded systems and even some involved in the development of scientific and technical personnel are also only single-chip, embedded systems do not know. This section from the beginning of the definition of embedded systems, embedded systems on the meaning, characteristics and so on, in order to enable readers to deepen their understanding of embedded systems.

基于2274液晶显示测试驱动，触摸屏教验程序-LCD drive for msp430 2274,cliber

单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。 编程使波形信号输出电路输出正弦波信号，并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10，共11个等级。 -Singlechip P1 I connect with the four buttons for the signal amplitude and frequency adjustment operation keys. Singlechip P0, P2.7, P3.6 (-WR) and DA0832, 2 months 741 (operational amplifier) to connect constitute waveform signal output circuit. Programming so that waveform signal output circuit output sine wave signal, and can be operated keys adjust the signal amplitude and frequency. Amplitude and frequency adjustment level from 0 ~ 10, a total of 11 grades.

MCS51单片机实现LCD1602显示汉字-MCS51 MCU LCD1602 display Chinese characters

CAN总线与51单片机的接口原理图，使用的是sja1000和tja1040(philips).还包括了具体的文档资料和c语言控制代码(附加了LCD代码和LCD接口以及电源变换原理图).搞CAN总线一步到位.-CAN Bus and 51 microcontroller interface schematics, using the sja1000 and tja1040 (Philips). Also include the specific information and documentation control code language c (Additional code of LCD and LCD interfaces, and power transformation diagram). CAN engage in one go.

MSP430单片机的DS18B20程序,自动识别ID号,可同时管理5个DS18B20,非常好用-MSP430 DS18B20 procedures, automatic identification ID, Management may also five DS18B20, very handy

用纯C语言实现C8051F单片机的在线程序更新-Using pure C language realize C8051F MCU online update

基于DS1820温度传感器,单片机控制的单线多路温度检测-Based on the DS1820 temperature sensor, single-chip microcomputer-controlled one-way multi-channel temperature detection