单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(

飞利浦的LPC2103的实验二：四位数码管动态显示0~F，分四次显示。编译环境为：keil3和proteus7，仿真通过。-Philips LPC2103 two experiments: dynamic display four digits 0 ~ F, four show. Compiler environment: keil3 and proteus7, through simulation.

是对sd卡驱动的分析以及读写分析寄存器配置-Is the sd card-driven analysis and analysis of reading and writing configuration registers

基于AT89C51和DS18B20的最简温度测量系统 温度检测的传统方法是使用诸如热电偶、热电阻、半导体PN结之 类的模拟温度传感器。信号经取样、放大后通过模数转换，再交自单片机处理。被测温度信号从温敏元件到单片机，-Based on AT89C51 and Jane DS18B20 most temperature measurement system temperature detection is the use of traditional methods such as thermocouples, thermal resistors, semiconductor PN junction, such as analog temperature sensor. Signal sampling, amplified through the analog-digital conversion, and then deal with pay since the single-chip microcomputer. The measured temperature signal from the thermo-sensitive components to the microcontroller,

鼠标应用程序示范 MCU AT89S51 XAL 12MHz 本程序可以实现鼠标的功能,并将位置显示在LCD上-Mouse model application MCU AT89S51 XAL 12MHz mouse in this program can realize the function, and location displayed on the LCD on

用于MSP430F247单片机的NOKIA5110液晶屏驱动程序-NOLIA 5110 LCD Driver For MSP430F247

这是一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算，而将所有参数全部用整数，运算 到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可大大提高运算速度，根据控制精度的不同要求，当精度要求很 高时，注意保留移位引起的“余数”，做好余数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。-This is a typical PID process, as in the use of SCM control cpu, please slightly simplified, specific PID parameters to be specific targets identified by experiments. As SCM processing speed and ram resource constraints, generally do not use floating-point operations, and will use all the parameters of all integers, and the final calculations to divide one of the Nth 2 data (the equivalent displacement), will count for a similar operation, it will greatly increase the computing speed, control Accuracy of different requirements and high precision, displacement caused reservations to the attention of the "I", which I do several compensation. This procedure is commonly used algorithm pid the basic structure does not include input and output processing.

sd卡mp3官方pcb文件，protel格式-sd card mp3 official pcb file, protel format

ADS7844串行模数转换芯片的原理及其在嵌入式的应用-ADS7844 analog-to-digital converter serial chip embedded in the principle and its application

Elan EM78P458 AD转换。

simpliciti1.0.4版本，在CC2430上通过实验-simpliciti1.0.4 version, the CC2430 on the experiments