for many computer enthusiasts, not often can be installed with a computer, throu...

CPLD Interface code with SRAM

设计并制作出汽车信号灯微机控制系统； 2）所需执行的操作由相应的开关控制，所需控制的信号灯有： 仪表板左/右转向灯、左/右头灯和左/右尾灯及左/右刹车灯共8个灯，其驾驶操作与灯光信号对应关系如下： (1)左/右转弯(合上左/右开关)：仪表板左/右转向灯、左/右头灯、左/右尾灯闪烁。 (2) 紧急开关合上：除左右刹车灯以外，所有灯闪烁。 (3) 刹车(合上刹车开关)：左右刹车灯亮。 (4) 左/右转弯并刹车：仪表板左/右转向灯、左/右头灯、左/右尾灯闪烁，左右刹车灯 亮。 (5) 合上紧急开并关刹车：仪表板灯、头灯、尾灯闪烁，刹车灯亮。 (6) 停靠(合上停靠开关)：头灯、尾灯以20Hz的频率闪烁。 -designs and produces vehicle lights microcomputer control system; 2) the implementation of the operation from the corresponding switch control, the control signals required : the dashboard left/right shift lights, left/right front and left/right rear and left/right brake lights a total of eight lights, driving its operation and light signals corresponding relationships are as follows : (1) Left/right handers (Hopewell on the left/right switch) : the dashboard left/right turn signals, left/right headlight, left/right rear flashing. (2) emergency switch matches : Apart from the brake lights around outside, all lights flashing. (3) brakes (a switch on the brake) : about b

一个用Labview编写的字符串转数字的程序-this program which develop by Labview is used to change character to number

《天降大便》这款游戏的源代码啊 《天降大便》这款游戏的源代码啊-恪缝降 戏 源 氚§降恪废?源 氚

并发程序公共包,用以打印日志，输出内容。-concurrent program package

从实用的角度详细介绍了RS纠错编码原理及其实现方法-From the practical point of view described in detail the principle of RS error-correcting code and its implementation

自己遍的牛顿迭代法求解二元二次方程的程序 迭代步数可以自己设定-Their times of Newton iteration procedure for solving the dual quadratic equation iteration step can be set for

本演示程序中，人数n应为任意的，首先应输入一个值赋给初始报数上限m，程序应能自动保存出列人的序号和将出列的人所持的密码赋给m，再次作为报数上限，如此循环，直至所有人都出列为止。-The demonstration program, the number n should be arbitrary, we must first enter a value assigned to the initial reported that the maximum number of m, the procedure should be able to automatically save a list of the serial number of people and held out the password assigned to m, again reported as the maximum number of such cycles, until all that far out.

linux下的USB和网络驱动程序代码，可以参考。-under linux USB and network driver code for reference.

指针变量往往是说是变量这点到另一个对象 .在一些 C 与指针和其他任务更容易执行编程任务。 A指针变量声明为 如下所示： 类型 * variable_name