AVR脉宽调整的程序，还可以！具有借鉴的价值！

基于C51的DS1820测温的C语言源程序，有详细注释-c51 program about tempreture data acquisiton

本系统参照片上系统的设计架构、采用FPGA与SPCE061A相结合的方法，以SPCE061A单片机为进程控制和任务调度核心；FPGA做为外围扩展，内部自建系统总线，地址译码采用全译码方式。FPGA内部建有DDS控制器，单片机通过系统总线向规定的存储单元中送入正弦表；然后DDS控制器以设定的频率，自动循环扫描，生成高精度，高稳定的5Hz基准测量信号。-The system with reference to the design of system-on-chip architecture, used a combination of FPGA and SPCE061A approach to SPCE061A Singlechip for process control and scheduling core mission FPGA for external expansion, internal self-system bus, address decoding using the entire translated code approach. DDS has built internal FPGA controller, microcontroller through the system bus to the provisions of the storage unit into the sine table DDS controller and then to set the frequency, automatic cycle of scanning, to generate high precision and high stability of the baseline measurement 5Hz signal.

液晶LCD1604+温度DS18B20+时钟DS1320 的C语言开发程序。及其在PROTEUS下的原理图-LCD LCD1604+ Temperature DS18B20+ Clock DS1320 C-language development program. And its application in the schematic diagram PROTEUS

鼠标的单片机驱动程序 把鼠标的四条线接在89c52 上把程序编译好后下载进去 就可使用。但要看好接口。-failed to translate

基于凌阳系列单片机的以太网驱动程序，已在SPCE61上调试通过-Sunplus series based on single-chip Ethernet driver has been SPCE61 debugging through

HZK24，单片机编程必备，基于UCDOS的24点阵-HZK24, single-chip programming necessary, based on the 24 lattice UCDOS

基于avr单片机的直流电机PID控制程序，工程文件的编译环境采用gcc for avr，可以在AVR Studio环境下调试，对电机开发人员具有参考价值。-avr microcontroller based on the DC motor PID control procedures, Project documents using gcc compiler environment for avr, the AVR Studio debugging environment, Development of motor officers with reference value.

这是DA的资料 这是DA的资料 这是DA的资料 -this is for DACthis is for DACthis is for DACthis is for DACthis is for DACV

编译环境：ICC AVR 6.31A 单片机：AT90S8515 PC.0出音乐信号，INT0，INT1分别接下一首、播放/暂停键 开机处于暂停状态，按下播放/暂停键开始放音，自动播放完8首，会再进入暂停状态。 所有的暂停状态都采用掉电模式。 -build environment : ICC AVR microcontroller 6.31A : AT90S8515 PC.0 musical signal INT0, INT1 respectively took one, Play/Zantingjian Boot suspended, press Play/Zantingjian start of audio, automatic broadcast End 8, will enter the state. All the suspended power-down mode is used.

51单片机P2口接4*4键盘的行线和列线；红灯亮时进行频率输入；绿灯亮时进行占空比输入；频率值暂定在100到60KHZ之间；输入频率和占空比时要输够六位整数，不够的在前面补0；占空比以百比数（0-100）形式存在。-51 Singlechip P2 mouth then 4* 4 keyboard line and column line red light when the frequency of input green when the input duty cycle frequency value is tentatively scheduled for between 100 to 60KHZ input frequency and duty than enough to lose six integers, not enough to fill in front of 0 duty cycle than a few hundred (0-100) form.