改进的胶印机印刷控制程序，效率提高5倍。

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

一个冒泡法排序（升序）的例子再进一步学习SPCE061A的编程，及调试。还有试验指导书，在电子书籍里找-A bubble method to sort (ascending) examples further learning SPCE061A programming and debugging. There are tests to guide books, find books in the electronic

ICC AVR6.25A ATMEGA16L芯片 LCD1602驱动程序-ICC AVR6.25A ATMEGA16L chip LCD1602 driver

计时器的设计，用单片机做的，很好用的，零件有饿很简单，希望大家喜欢-timer design, MCU done, the good parts are hungry very simple hope you like

实现简单的串口传输工作! 有数据检验,汇编程序!-Realize a simple serial transmission work! Have data verification, compilation procedures!

：章介绍了数据采集系统中STC12系列单片机与PC机之间的串行通信。设计了sTc12c2052AD 与 MAX232的硬件电路，使用汇编语言编程，设置了串行1：7的工作方式，相应的波特率计算方法及特点，发送并接 收数据。单片机从EEPROM 中读取数据，通过R．S-232将其传入PC，并将数据存储在24C02中。-: Chapter introduces data acquisition system STC12 Series MCU and PC serial communication between machines. Designed sTc12c2052AD with MAX232 hardware circuit, the use of assembly language programming, set up the way the work of serial 1:7, the corresponding baud rate calculation method and the characteristics of sending and receiving data. Single-chip EEPROM read data from, by R. S-232 to incoming PC, and data storage in the 24C02.

keilc51 startup代码解释 -keil c51 startup source code explain

本程序又是一个单片机的简单例程，含电路图及C程序，可参考-This procedure is a simple and routine single-chip, including circuit diagrams and C procedures, can be found! !

很好的字模提取工具！能够大大加快开发字模显示程序的开发！比如说：液晶显示，led点阵模块的数据显示！-good Abstraction tool! Able to greatly accelerate the development of character mode display program development! For example : LCD, led dot matrix module data show!

对另一单片机传送过来的编码电平进行译码。并在16002上显示出接受到的字符-Transfer over to another microcontroller to decode the coding level. And 16002 characters on the show receive