这篇文章发表在《单片机与嵌入式系统应用》2005年第三期，我已经和彭先生联系上了！他会回答大家的问题的 2002年初，笔者着手写一个IC卡预付费电表的工作程...

利用NRF9e5芯片编写的C51源代码，可实现点到点无线通信接收部分。-NRF9E5 chips prepared using C51 source code, can be achieved to receive part of point-to-point wireless communications.

完整的c程序，包括模拟量输入输出，pid算法，触摸屏通讯等。-Complete c procedures, including analog input and output, pid algorithm, touch-screen communications.

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

合二为一的JTAGICE仿真器和ISP编程器全套资料,本人已实验成功-JTAGICE simulation combined ISP programmer and a full set of information, I have conducted successful experiments in

串口程序源码，增强版！mega16系列的！-Serial program source, enhanced version! mega16 series!

直流电机反转控制程序,使用L298N,C语言编写-DC motor control program

CC2430 基础实验十一 1/3AVDD的实验-CC2430 11 experiments 1/3AVDD the basis of the experimental

详细介绍了如何利用C51来设计ET6201 LED驱动芯片的程序，适用于DVD/CD等电子产品的显示面板

利用8279芯片实现通过2X8键盘输入加数和被加数并计算出结果，同时将加数、被加数和结果都在LED灯上显示出来。-Chip 8279 through the use of 2X8 and keyboard input addend addend and calculated results, at the same time, addend, addend and the results were in the LED lights on the display.

通过日期算星期的C51源程序,用c写的小程序 希望对大家有用-through weeks of the date of counting source of C51, with a small c written procedures hope useful for all