passive component schematic library for altium

给出了沉浸式虚拟维修仿真系统的框架，从样机建模和交互技术两个方面对其关键技术进行了研究．提出 了虚拟维修样机的概念，通过定义样机部件的约束运动和交互特征来实现其所要求功能，而交互技术则主要集中在 抓取和防穿越处理上．建立了基于Jack系统的沉浸式虚拟维修仿真原型系统，并以某机构的拆装为例对其进行了初 步的应用验证-Give the Immersive Virtual Maintenance Simulation System framework, from prototype modeling and interactive technology for its two key technology areas were studied. Put forward the concept of a virtual prototype of repair, by the definition of prototype components bound to exercise and interactive features of implementation of its functional requirements, and the interactive technology was mainly concentrated in the crawl up and deal with anti-crossing. Jack set up a system based on Immersive Virtual Maintenance Simulation prototype system and the dismantling of an institution as an example of its application for a preliminary verification

XILINX 开发板，原理图主要由XC4000和一个8031构成-XILINX development board, mainly by the XC4000 Schematic and 8031 constitute a

一个不错的案例运行典范，实际操作的手册，关键步骤的说明-a good example of the operation of cases, the actual operation of the manual steps of the key

摘要:基于通信技术的列车运行控制系统(CBTC)是铁路信号的发展方向，交频分复用 OFDM)是一种无线环境下的高速传输技术，它对高速列车控制信息传输中卞要受到的由于多 径传播引起的快衰落所产生的影响有很强的抵抗能力.本文首先介绍了OFDM技术的发展和 基本原理，然后在计算机上用M atlal〕对其性能进行了仿真，仿真中将OFDM与传统的单载波 调制方式―i1，交振幅调制( 1frQAM)对抗多径十扰的性能进行了比较，最后分析了一者的仿真结果. -Abstract: Based on the communication technology train operation control system (CBTC) is a railway signal direction for the development of cross-frequency division multiplexing OFDM) is a wireless environment of high-speed transmission technology, its high-speed train control information transmission Bian be subject to the Due to the spread of multi-path fast fading caused by the impact of a strong resistance to diseases. This paper first introduces the OFDM technology development and the basic principles, and then on the computer〕 M atlal use its performance simulation will OFDM with the traditional single-carrier modulation-i1, cross-amplitude modulation (1frQAM) against multi-path interference of the 10 properties were compared with a final analysis of

CF卡的规范，对那些开发CF卡驱动的同志很有帮助的。-CF card standards developed for those comrades CF card driver very helpful.

Java即时通信工具(JICQ)设计文档演示 ppt格式,设计文档演示,安装powerpoint查看-Java instant communication tools (JICQ) design presentations ppt format, design presentations, installation powerpoint View

robotics engineering introduction

文中介绍一种不用光耦就可以实现隔离的方法-This paper introduces an optocoupler can be achieved without isolation method

提出了一种用于矢量量化的改进的聚类算法,该算法在MKM(Modified K-Means)算法的框架的基础上,对初始码本的生成、失真测度的选择、非典型胞腔的处理等方面进行了改进,从而减少了原算法在能量和增益上对聚类结果的影响.并将该算法应用于波形编辑孤立字识别器,这种识别器直接对语音样本的时域波形进行训练和聚类,不需要提取语音参数,算法复杂度较低,加上提出的聚类算法失真测度简单易实现,对芯片的运算能力要求不高,非常适用于有低成本要求的语音识别器场合.通过中文元音字识别的实验证明,在相同码本尺寸下,运用改进后的聚类算法的识别器的识别率有所提高. -A Modified MKM Clustering Algorithm and Its Application in Speech Recognition

介绍了无线传感器节点的设计与实现，以CC2430芯片为核心，利用烟雾传感器设计电路，并通过无线收发模块与网络协调器和上位机通信达到监控目的。-Describes the wireless sensor node design and implementation, in order to CC2430 chip as the core, the use of the smoke sensor circuit, and through the wireless transceiver module and the network coordinator and the host computer to control the purpose of communication.