用AT89S51单片机制作的一个带通讯的数字电压表，内含电路原理图及汇编源程序代码，以及数张图片，还有论文和设计感想。倾力奉送！...

一个基于mc9s12dg128b，时间捕捉器的示例代码-Based on mc9s12dg128b, time catcher of the sample code

c8051f020 内部12位的ADC0 效果比较啊好,调通了 如果不行 我还有其他人写的一个程序.我传的代码都有比较爱完整的注释啊-C8051F020 within 12 compared the effect of the ADC0 ah well, if the transfer had not I still have other people write a program. I have compared the code Chuan Love Notes integrity ah

介绍了集成温度传感器AD590，给出了AD590测量热力学温度、摄氏温度、两点温度差、多点最低温度、多点平均温度的具体电路，并以节能型温、湿度控制系统为例介绍了利用AD590测两点温差电路的应用。-Introduced an integrated temperature sensor AD590, given AD590 measuring thermodynamic temperature, Celsius temperature, two temperature difference, multi-point minimum temperature, average temperature of the specific multi-point circuits, and to energy-efficient temperature and humidity control system as an example, introduced the use of two AD590 temperature measurement circuit applications.

完成了802.15.4协议中MAC层的工作，其主要功能就是完成了透明的无线传输-Completed the MAC layer in 802.15.4 work, its main function is completed transparent wireless transmission

用于手持时钟受时，时钟芯片的工作稳定性，以D18B20温度传感器的采集，微调时钟芯片的内置电容，改变震荡频率-For hand-held by the clock, the clock chip of job stability to temperature sensor D18B20 collection, fine-tuning of the built-in clock chip capacitors to change the vibration frequency

eo2c5 实现 led 键盘控制 verilog 编程-keyboard led control to achieve eo2c5 programming verilog

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

万年历+温度+12864LCD，51单片机程序，proteus仿真，很好的-Calendar+ Temperature+ 12864LCD, 51 single-chip program, proteus simulation, good

芯片PCF8951共有四个A/D输入通道：AD0，AD1，AD2，AD3,分别与四个电位器(R1,R2,R3,R4)连接，用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压，也可用于测量从J1插座输入的外接电压，须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据。-PCF8951 chip, there are four A/D input channels: AD0, AD1, AD2, AD3, respectively, with four potentiometers (R1, R2, R3, R4) connected to regulate the output voltage potential. AD0 channel which can be measured potentiometer output voltage can also be used to measure the input from the J1 socket external voltage, to be used to select switch J2. J4 socket output from the PCF8591 clock square wave signal. SAA1064 drivers of four digital display along after AD conversion data.

很好的单片机控制继电器代码，与大家分享-Good single-chip microcomputer to control the relay code to share with you