SCM RS485 communication

介绍了液晶显示模块基本原理及其技术特性，与单片机的进行接口的具体电路，同时给出了其编程方法和程序代码．-Introduced the basic principles of liquid crystal display module and its technical characteristics, and MCU interface to the specific circuit, at the same time gives the methods and procedures of its programming code.

51系列单片机的uCOS-II原代码-51 Series MCU uCOS-II source code

IAR例子，里面是一个完整的串口异步通讯例子。-IAR examples, which is a complete example of serial asynchronous communication.

C51源代码，驱动74164》，这个程序太简单了，不过省得大家自己写了-C51 source code, drive 74164

本设计的由单片机控制的自动加料系统是与料斗式干燥机配套的加料系统。根据加料工艺要求，其工作原理是：先将真空管关闭，启动电机，用低真空气流将塑料树脂粒子送入真空管，电机停转，再将粒子排入料斗，如此循环。-The design of single-chip microcomputer controlled by the automatic feeding system with hopper dryer feed supporting system. Charging process in accordance with the requirements of its working principle is: first vacuum tube to close, start motor, using low vacuum plastic resin particles will flow into the vacuum tube, the electrical switch to stop, and then particles into the hopper, and so the cycle.

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

该代码包介绍了基于51系列单片机平台是实现时间触发的嵌入式系统的各种应用的代码-the code based on the Series 51 platform SCM is the time to trigger the Embedded System Applications code

单片机红外遥控最全的资料，包含很多当前电视遥控专用芯片的解码方式，C语言和汇编语言编写的解码范例程序，看完了你就会了！-infrared remote control MCU most complete information, including many current television remote control decoder ASIC, C and Assembly Language prepared by the example of decoding procedures will be watching you!

sht11 与51单片机驱动c代码 t11 与51单片机驱动c代码-sht11 connected to mcs51g