金蓬噢科拉图形液晶显示器ocm8系列并口驱动程序。

8019sch网络芯片 带PCB图 8019sch网络芯片 带PCB图-8019sch network chip with PCB Figure 8019sch network chip with PCB diagram

该源代码为单片机的公交ic卡课程设计源代码，需要课程设计报告的，再找我。-The source code for the MCU bus ic cards curriculum design source code, the need for curriculum design report, I find.

芯片PCF8951共有四个A/D输入通道：AD0，AD1，AD2，AD3,分别与四个电位器(R1,R2,R3,R4)连接，用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压，也可用于测量从J1插座输入的外接电压，须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据。-PCF8951 chip, there are four A/D input channels: AD0, AD1, AD2, AD3, respectively, with four potentiometers (R1, R2, R3, R4) connected to regulate the output voltage potential. AD0 channel which can be measured potentiometer output voltage can also be used to measure the input from the J1 socket external voltage, to be used to select switch J2. J4 socket output from the PCF8591 clock square wave signal. SAA1064 drivers of four digital display along after AD conversion data.

AT89C51单片机的超声波测距的原理图及汇编程序-AT89C51 microcontroller schematic diagram of ultrasonic ranging and assembler

Atmel Atmeag128 AVR弹片机 随书原码

这是一个GPS方面的资料，可供想在嵌入式方面编程的人员参考-This is a GPS information, can be like in the embedded programming staff members

ali3355源码: 1.OBJS目录:编译目录 命令: ./clean.sh ./55product.sh 2.serve:光头部份程序 3.source:介面与播放有关项目.-ali3355 Source : 1.OBJS Contents : build directory order : ./clean.sh ./55product.sh 2.serve : Bald some procedures 3.source : interface with the broadcast of the project.

风机控制器智能程序5,请大家自己使用,千万不外传!-Intelligent fan controller program 5, let us own use, do not Gaiden!

基于pic单片机的嵌入式系统的以太网通信的软件程序，可以实现pic单片机以太网开发板的网络功能，以及学习TCP/IP协议栈的使用方法-Pic based on the Embedded System Single Chip Ethernet communications software program, can achieve single-chip Ethernet development board pic of network functions, as well as learning TCP/IP protocol stack to use

本设计的由单片机控制的自动加料系统是与料斗式干燥机配套的加料系统。根据加料工艺要求，其工作原理是：先将真空管关闭，启动电机，用低真空气流将塑料树脂粒子送入真空管，电机停转，再将粒子排入料斗，如此循环。-The design of single-chip microcomputer controlled by the automatic feeding system with hopper dryer feed supporting system. Charging process in accordance with the requirements of its working principle is: first vacuum tube to close, start motor, using low vacuum plastic resin particles will flow into the vacuum tube, the electrical switch to stop, and then particles into the hopper, and so the cycle.