320*240点阵液晶模块驱动程序,控制芯片为SED1335；128*64点阵液晶体驱动程序，控制芯片为ks0108....

AVR单片机开发的AT24C02的I2C实验-AT24C02 single-chip AVR development of I2C experiment

AD0809做的电压表 有这方面需要的可以参考参考-AD0809

ds2482-100是IIC协议转1-wire协议的接口芯片。本程序包利用ds2482-100操作温度传感器ds18s20。注意：ds18s20初始化后温度值为85摄氏度，必须多读几次温度以便其显示稳定。另外，文件中包含的一些头文件可以顾名思义，都是比较通用的（如IIC软件包），为节省篇幅，没有包含进来。请在 编译时自己根据接口函数添加。-ds2482-100 is IIC agreement to 1-wire agreement interface chip. The packages use ds2482-100 ds18s20 operating temperature sensor. Note : After initialization ds18s20 temperature of 85 degrees Celsius, to be read several times the temperature to show its stability. Also, the document contains a number of header files can name suggests, are relatively common (eg IIC package), To save space, are not included come. Please compiled under its own interface function was added.

步进电机加减速计算 说明输入步进电机的加减脉冲步数,就可计算出电机加减速的静态表(16进制输出)-motor s type download

12864LCD(带汉字库)显示遥控键值读取器 * * LCD型号：TS12864A-3（带汉字库）或兼容型号 控制器ST7920 * * MCU:AT89S52 ,晶体频率：11.0592MHz * * P0口为128*64LCD的数据 D0-D7 * * K17键按下，继电器吸合。K19键按下，继电器关闭 * * 显示程序在中断服务程序之中-12864LCD (with汉字库) shows the remote control key reader** LCD Model: TS12864A-3 (with汉字库) or compatible controller Model ST7920** MCU: AT89S52, crystal frequency: 11.0592MHz** P0 population is 128* 64LCD data D0-D7** K17 button pressed, the relay pull-in. K19 button pressed, the relay to close** display program in the interrupt service routine of

短距离无线通信技术zigbee协议栈c源码，Microchip公司版本-short distance wireless communication technologies zigbee protocol stack c source, Microchip version of the company

基于80C51单片机源码公开的操作系统1.20.2 版RTOSsmall_rtos1.20.2-80C51 microcontroller based on the open-source operating system version 1.20.2 RTOSsmall_rtos1.20.2

是一个电话接口模块，它给你提供一个自动检测电话是否正常，电话是否连通。-is a telephone interface module, which gives you an automatic detection normal telephone, whether telephone connectivity.

PCF8563 的驱动程序，用两个普通的IO口模拟I2C总线，包括100KHZ（T=10US）的标准模式选择和400KHZ的快速模式选择，默认11.0592MHZ的晶振-PCF8563 of the driver, with two ordinary analog IO I2C bus, including the extremely low distortion (T = 10US), the standard model selection and 400KHZ fast mode selection, the crystal default 11.0592MHZ

EEPROM24c16读写程序，需要的可以参考一下-EEPROM24c16 read and write procedures, needed for reference