ide68k“68000集成开发环境

应用背景 keil stm32 f4 mpu6050 测出 加速度 角加速度  转换滚转角等 用p8 p9 iic采集  uart1串口输出  stm串口转ttl模块连电脑  匿名上位机 处理数据 关键技术 keil上写的mpu6050 Iic数据采集 正点原子里的mpu是自己焊好的引脚配置时考虑了电路，用其他不同的F4时有余引脚原因会读不出数据，需更改其中应答。

下面是一个超声波测距的程序，硬件电路由于电脑格盘已丢失，下面的代码是从样机上复制的。 硬件电路包括液晶显示、超声波的发射、超声波的接受、滤波、单片机处理。 液晶显示采用LCD1602模块，下面的代码里有液晶的驱动，可以拷贝用于它处。 超声波发射电路包括压电换能器及其支持电路，发射约44KHz的超声波。 超声波的接收电路包含一块CD40106处理芯片。技术指标大约是测距范围在三米左右，测量精度约在厘米级别。大量用于倒车雷达的测距中。-The following is a range of ultrasound procedures, the hardware circuit as a result of the computer grid plate has been lost, the following code is copied from the prototype. Hardware circuit including liquid crystal display, ultrasonic transmitter, ultrasonic acceptance filtering, single-chip processing. LCD1602 LCD module used, the following code, there are LCD drivers, you can use it to copy. Firing circuit including the piezoelectric ultrasonic transducer and its support circuitry, fired about 44KHz ultrasound. Ultrasonic receiver circuit includes a processing chip CD40106. Technical indicators for a range of about 3 meters range around the measurement precision level of about cm. Reversing a large number for the location of the radar.

fs2410 红外解码程序！ -fs2410 infrared decoder program! fs2410 infrared decoder program!

MSP430F5438初始化程序,针对于MSP430F5438 编写的底层驱动，其中包含URAT,TIMEA,TIMEB,AD等模块的初始化

豪华板中E35G23的UCOS2+UcGUI图形系统2.76，UCOS_II测试程序说明，由hgxxx的ucosii2.71升级而来的！去掉了TaskLcd running显示，把这个任务作为GUI显示输出，类似于UCOS的例子1，在一个随机的位置显示一个随机数，只是允许一个任务调用GUI，没有显示cpu利用率、切换次数等信息！注意：~本程序适用于240×320 16级灰度液晶！去掉了TaskLcd running显示，把这个任务作为GUI显示输出，类似于UCOS的例子1， -luxury plate E35G23 the UCOS2 2.76 UcGUI graphics system, UCOS_II test procedures provided by the ucosii2.71 escalation hgxxx come! TaskLcd removed from the running has shown that this task as shown GUI output UCOS examples similar to the one in a random location of a random number, allow only one task calling GUI, no indication of cpu utilization, switching frequency information! Note : ~ procedures applicable to the 240 x 320 16-greyscale LCD! TaskLcd removed from the running has shown that this task as shown GUI output UCOS similar to the one example,

嵌入式软件开发.rar-embedded software development. Rar

linux下块设备block驱动程序源代码分析。-under linux block block device driver source code analysis.

基于arm的linux操作系统的minGUI图形库，是较好的GUI，比QT要简洁，代码的集成度高，是很好的参考程序-based on the Linux operating system arm of minGUI graphics library, the GUI is better than QT to be concise, code integration, is a good reference program

ARM LINUX在EP7312上的移植 是个PDF文档，有做这方面的可以参考！-ARM LINUX on transplantation in the EP7312 is a PDF document, has to do in this area can refer to!

24c02读写程序-24c02 literacy procedures