记录了汽车CAN总线通信环境的建立和初始化

keil c程序,用于AT89S52单片机.使用了T2计数器,有频率计的功能-keil c program for single-chip AT89S52. the use of the T2 counter, there is the frequency of functional

这是我在学校做电子钟留下的资料 希望能给你带来帮助-This is my electronic bell in the school do hope that they will be left behind by the information to help you

是最新单片机c8051f0xx 的一本中文电子书-Is the latest single-chip c8051f0xx of a Chinese e-books

ARM里实现 PWM ARM经典 C语言写的-ARM achieve PWM

通讯规则: 1:时钟7.3728 MHz/波特率9600/9个数据位/奇校验/1个停止位/硬件多机通讯功能/ 2:通讯连接采用硬件MAX485,双向单工 3:每个上行/下行的数据包的字节个数都是一样的(通讯数据量) 4:每个上行/下行的数据包都采用CRC8校验 5:数据接收采用中断+查询的方式 6:总是由主机向从机发送一个数据包,从机收到数据包后向主机回复一个数据包 7:不管是主机还是从机,如果收到的数据包有任何错误,都将丢弃该数据包,等效于没有接收 8:从机之间不能相互通讯,必须通过主机才能交换数据 9:无效地址是0,主机地址是1,从机地址是2.3.4......广播地址是255 -err

采用步进电机模拟洗衣机电机，实现上水、浸泡、洗涤、漂洗、甩干等过程。洗涤分弱洗、轻洗、强洗；可设定3级水位设定，每级水位均设定水位下限（值自定）；可选择漂洗次数（3~5次）。使用键盘进行流程及参数设定及自动存储流程，设定暂停键，可暂时停止洗衣机的工作，恢复后按原设定程序继续进行，同时设定停止键，可终止洗衣机的工作，并在LED或LCD上显示当前流程。-Simulation using stepper motors washing machine motor to achieve Sheung Shui, soaking, washing, rinsing, drying and other processes. Washing sub-weak wash, light wash, strong wash can be set to three water level settings, set the water level in each grade level were lower (the value of self-set) optional rinsing times (3 ~ 5 times). Using the keyboard processes and parameter settings and automatic memory processes, set pause button to temporarily suspend the work of washing machines and restore original settings after the process to continue at the same time set the stop button, may terminate the work of washing machines, and LED or the LCD displays the current process.

香港科大机器人资料 单片机相关知识，开发平台多样-HKUST Information Singlechip robot-related knowledge, development platform for diverse

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

介绍利用单片机实现温度的远程显示的文档，利用RS485总线-introduces MCU temperature remote display documents, the use of RS485

P89CXX编程器控制CPU接收和控制程序-P89CXX Programming Control CPU to receive and control procedures