-
在C++写PCI9052驱动代码
基于windriver的pci驱动程序源代码,我现在项目开发已经调试好的代码
-pci9052 driver code write in c++
- 2022-02-14 22:28:31下载
- 积分:1
-
PCI总线仲裁参考设计Verilog代码
PCI总线仲裁参考设计Verilog代码-PCI bus arbitration reference design Verilog code
- 2022-02-20 02:42:05下载
- 积分:1
-
与 24 c 04 eeprom 的 pic 16f877a
它是 I2c 基于接口的 24 c 04 EEPROM 与 pic 16f877a 使用 xc8 编译器。每个函数在编码被命名为它的使用的目的。所以这个程序是很容易理解......:)希望充分......最佳 regardsMotasim
- 2023-01-30 21:25:04下载
- 积分:1
-
an encode program of pseudo
伪随机序列编码源程序-an encode program of pseudo-random sequence
- 2022-03-09 14:19:08下载
- 积分:1
-
RS232 switch to RS485 circuit diagram and the finished document serial pcb to ta...
RS232转RS485电路原理图与成品pcb文件 串口取电!-RS232 switch to RS485 circuit diagram and the finished document serial pcb to take power!
- 2022-03-23 23:25:06下载
- 积分:1
-
His transplant UC/0S_II to tq2440 development board hardware drivers GUI
自己移植UC/0S_II 到 tq2440开发板 GUI 硬件驱动-His transplant UC/0S_II to tq2440 development board hardware drivers GUI
- 2022-03-16 15:27:17下载
- 积分:1
-
总的来说,在uClinux上的开发和标准Linux还是很类似的。通常可以按照下面的步骤去设计和调试: 建立基于以太网的开发环境; 如果所设计的程序和硬件的关联不...
总的来说,在uClinux上的开发和标准Linux还是很类似的。通常可以按照下面的步骤去设计和调试: 建立基于以太网的开发环境; 如果所设计的程序和硬件的关联不大,那么一定要在标准Linux上先编译和调试通过。灵活地使用gcc和gdb将大大节省时间; 将x86上的GCC编译好的应用程序用交叉编译工具来编译;如果编译时发现错误,那么很可能存在以下问题: 交叉编译器或库文件的路径不正确;最彻底的解决办法是重新装一次编译器; 遇到库不支持的函数;此时需要自己把函数的实现做成另外一个库供应用程序使用。如果是uClinux本身不支持的调用,那么就需要改写代码了。-Overall, the uClinux on the development and standard Linux is still very similar. Usually can use the following steps to design and debug : Ethernet-based development environment; If the design of the procedure and not linked to the hardware, then it must be the first standard Linux compiler and debugging through. Flexibility in the use of gdb and gcc will greatly save time; X86 will be on the GCC-compiled application with cross-compiler tool to compile; If you compile time error is found, it was very likely that the following issues : cross-compilers or libraries are not the correct path; The most radical solution is a re-installed time compiler; encountered does not support functions; At this time the need to
- 2022-10-25 13:50:03下载
- 积分:1
-
P18F452的uCosII的源码
P18F452芯片的uCosII的移值,详尽的描述了各个接口,以及与芯片的应用,并有例程,可实际使用
- 2022-05-29 01:31:00下载
- 积分:1
-
原创cc2500在stm8上的驱动程序,IAR 621环境,50万件产品销售无故障
小原创cc2500在stm8上的驱动程序,IAR 621使用环境。原文参考ST原版程序。
程序优化,设置3种程序发送完成检测模式,系统IO口不足时,可省GDO0.
状态转换极为迅速。目前已累计产品销售超50万件无故障
- 2022-06-11 14:36:38下载
- 积分:1
-
这是韩国原版X
这是韩国原版X-Hyper250B开发板的原代码。在LINUX下编译,对ARM开发的有重要助啊。--Source code for X-Hyper250B developing board. It is compiled in LINUX and is helpful for developing ARM.
- 2022-07-10 23:28:31下载
- 积分:1