EEPROM仿真有原理图，源代码，如详细的描述…

虽然很多人都知道FFT是什么，可以用来做什么，怎么去做，但是却不知道FFT之后的结果是什意思、如何决定要使用多少点来做FFT。-Although a lot of people know what is the FFT can be used to what to do, how to do, but do not know the results after the FFT is a very mean, how to decide how many points do want to use FFT.

尽量朝“单片”方向设计硬件系统。系统器件越多，器件之间相互干扰也越强，功耗也增大，也不可避免地降低了系统的稳定性。随着单片机片内集成的功能越来越强，真正的片上系统SoC已经可以实现，如ST公司新近推出的μPSD32××系列产品在一块芯片上集成了80C32核、大容量FLASH存储器、SRAM、A/D、I/O、两个串口、看门狗、上电复位电路等等。 -North Korea as the "single-chip" design direction of the hardware system. System devices more mutual interference between devices are more strong, power consumption is increased, it will inevitably reduce system stability. With MCU with on-chip integration of more powerful, the real system-on-chip SoC can achieve, such as ST"s new PSD32 x x in a series chip integrates exertion nuclear, large-capacity flash memory, SRAM, A/D, I/O, 2 serial port, watchdog, the power-on reset circuit and so on.

使用凌阳单片机，控制5088编码芯片编码并传输到8870解码芯片，得到所需数字信号。-Sunplus use single-chip, chip encoding control code 5088 and transmitted to the 8870 decoder chip, get the digital signal.

实现串口通讯的uvision工程，对学习汇编和单片机很实用。-To achieve serial communication uvision projects, learning is very useful compilation and SCM.

这是一个音量控制IC，采用IIC通信方式，容易控制，价格便宜。-This is a volume control IC, the use of IIC communication, easy to control and cheaper prices.

基于单片机的波形发生器，可产生方波，三角波及正弦波，频率可调。-Based on single-chip waveform generator to generate square wave, sine wave triangle spread, frequency adjustable.

使用avr90can32双串口传输蓝牙数据-Avr90can32 dual-use Bluetooth serial data transmission

在LED上显示中文汉字的源代码，采用汇编语言，对于入门者帮助很大。-LED display Chinese characters in the source code, using assembly language is very helpful for beginners.

自己现在用的51系列单片机下载线，用74HC373芯片 PCB-himself with the 51 series microcontroller downloaded line with 74HC373 chip PCB

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]