在PIC上实现CRC16算法的源程序，可用于一般通讯中的校验。

数码管显示秒表(汇编),用动态扫描的方式进行显示，减少IO口-Digital display stopwatch (compilation), with dynamic scan showed that the way to reduce the IO I

8051串行通信教程

当按下开关SP1，AT89S51单片机产生“叮咚”声从P1.0端口输出到LM386，经过放大之后送入喇叭。 -When pressing the switch SP1, AT89S51 Single-chip a " ding dong" sound from the output port P1.0 to LM386, after amplification into speakers after.

这个范例说明如何使用8051 的Port 1连接LCD显示器，PORT 3.3、P3.4和P3.5则连接到LCD显示器的控制线。程序执行时将显示出Hello Keil C和LCD display */-This example shows how to use the 8051 Port 1 to connect LCD displays, PORT 3.3, P3.4 and P3.5 are connected to the LCD display control lines. Program execution will show Hello Keil C, and LCD display* /

本文介绍了一种电子密码锁的实现。该电子密码锁采用1一wire总线芯片Ds2401作为密匙，锁体采用高可靠性的单片机PIC16c63来完成密码识别和开锁控制，用I2C总线接口的EEPROM 芯片AT24c02来完成密码的存储和修改，可 掉电保存密码。整个系统安全可靠，稳定性高。-This paper introduces an electronic code lock realize. The electronic locks used one chip one wire bus Ds2401 as key, lock body for high reliability PIC16C63 microcontroller identification and password to complete the unlock control, with I2C bus interface EEPROM chip AT24C02 to complete the password storage and revised down to save the password. The entire system is safe and reliable, high stability.

这是TLC5620的单片机试验程序,用KEIL环境,适合51单片机初学者-This is the single-chip TLC5620 testing procedures, using KEIL environment, suitable for beginners 51 Singlechip

CC1000为RF芯片，作为无线通信处理芯片，本程序是基于PIC72作为处理器。频段为433.92M，具有多种通信方式，通信速度可达到65K。-CC1000 RF chip, as wireless communications processing chip, the procedure is based on the PIC72 as the processor. For 433.92M band with a variety of means of communication, communication speeds up to 65K.

LCD常用取模软件,还行-LCD common modulus of software, but also line

软件UART示例 两个完整的例子,一个用PCA为波特率发生器的C语言程序和一个用定时器0为波特率发生器的汇编语言程序. 适用于下列器件 C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236-Software UART Examples of two complete example, a baud rate generator with PCA for the C language program and a use timer 0 baud rate generator for the assembly language program. C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236 applies to the following devices

矢量变频器控制源程序-vector converter control program