系统能够产生正弦波、方波、三角波。同时还可以作为频率计测频率。函数信号的产生由MAX038和外围电路完成，能产生1Hz―20MHz的波形。...

PIC单片机的几个设计实例,不可多得！-PIC several design examples, rare!

凌阳061a单片机的基本使用例程。包括两个基本实验的源代码-Sunplus 061A Singlechip the basic use of routines. Two basic experiments, including source code

at89c5131 实现 mass storage 的源码.-AT89C5131 realize the source mass storage.

矩阵键盘键值显示和液晶程序-LCD．汇编-Matrix liquid crystal display and a keyboard key process-LCD. Compilation

通过串口，接收上位机发送的命令，并进行CSI24WC02的读写操作，并返回相应 数据或应答。用汇编实现,可以用keil编译器-through the serial port, the receiving PC to send orders, and CSI24WC02 read and write operations, and return to the corresponding data or response. Assemble realized, can be used Keil compiler

串口调试工具，对于调试单片机和计算机通信相当有用哈。-Serial debugging tools, for debugging single-chip computer and computer communication very useful in Kazakhstan.

单片机编程的bcd码和hex码的互换，BCD2HEX 例子： c=BCD2HEX(0x255) //255 转成HEX为0xff c=HEX2BCD(0xff) //0xff 转成BCD码为 2-microcontroller programming bcd yards and hex code swap BCD2HEX example : c = BCD2HEX (0x255)// 255 to HEX conversion c = 0xff HEX2BCD (0xff)// 0xff conversion of 255 BCD

c51无参数调用asm-decoder called with no arguments asm

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

利用ＺＬＧ／ＳＤ软件包以及串口间件，数据队列软件包，构造一个ＳＤ／ＭＭＣ卡读卡器．-Use ZLG/SD software packages as well as the serial inter-pieces, data queue package, construction of a SD/MMC card reader.