/// ////单端输入，定时启动，由T2定时，选择AIN0.3为ADC0转化通道//////////////// //////single.c//////...

/* 程序详细功能介绍： *当按下按键P3.3 ，AT89S51单片机产生“叮咚”声从P3.2端口输出 *程序设计方法 * 1． 我们用单片机实定时/计数器T0来产生700HZ和500HZ的频率，根据定时/计数器T0，我们取定时250us， * 因此，700HZ的频率要经过3次250us的定时，而500HZ的频率要经过4次250us的定时。 * 2． 在设计过程，只有当按下SP1之后，才启动T0开始工作，当T0工作完毕，回到最初状态。 * 3． “叮”和“咚”声音各占用0.5秒，因此定时/计数器T0要完成0.5秒的定时，对于以250us为基准定时2000次才可以。 */-/* Procedure detailed functional Introduction:* When pressing the button P3.3, AT89S51 Singlechip a

基于MSP430单片机的，GPRS源代码，已经调试成功。-MSP430 MCU-based, GPRS source code, debugging has been successful.

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

PHILIPS LPC900 PWM CRTL 时间可调 -PHILIPS LPC900 time adjustable PWM CRTL

keil 环境 收IR及发IR的相关软件-keil environmental collection of IR and IR-fat related software

51单片机浮点子程序库(大型),直接嵌入,方便使用.-51 single-chip floating-point subroutine library (large), direct embedding, user-friendly.

PIC单片机的定时器使用的demo程序.内附说明.-PIC MCU timer used demo program. Containing a note.

基于TI的MSP430的方面的相关的软件和MSP430的相关的资料.-based on TI"s MSP430 aspects of the software and MSP430 relevant information.

红外线遥控解码器,该程序实现将红外遥控器发出的红外线解码，并通过LCD显示出来 -infrared remote control decoder, the program will infrared remote control and using the infrared decoding, and out through the LCD display

用msp430 对128×64的LCD的完全操作， -Controller with 128 64 LCD full operation,