一个sonix的仿51单片机指令macro,在写汇编时超好用，可读性超强...

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

这篇实验报告是关于单片机多路数据采集的，本实验由2大部分组成：1、为用EPOROM构成的心电信号发生器；2、为多路信号的微机采集与显示；第一部分实验主要研究可编程序存储器EPROM的非计算机应用。把存储在EPROM中的数字心电信号读出并通过D/A转换为模拟信号显示在示波器屏幕上。 第二部分实验的目的是研究一个数据采集系统，该系统利用ECD-51型单片机为中心，由D/A芯片等将各种低频信号以及由EPROM产生的模拟人体心电信号变换成离散的数字信号存入微机内存，以待进行数据处理和分析，然后再通过D/A转换将其还原成模拟信号显示在示波器的屏幕上。 -This experimental report on the multi-SCM data acquisition, the experiment by the two major components : 1. EPOROM pose for the use of the ECG signal generator; 2, multi-path signals in the computer acquisition and display; the first major study of experimental programmable EPROM memory in non-computer applications. Stored in the EPROM of ECG read out by D/A conversion of analog signals displayed on the oscilloscope screen on. Part II The purpose of this experiment is to study a data acquisition system, which uses ECD-51 microprocessor as the center, from the D/A chips, and other various low-frequency signal from EPROM and the simulation of human ECG transform into several discrete signal words into computer mem

keilC芯片选择可以看出STC中不需要包含

此为友善之臂micro2440板的核心板原理图，更新时间是2009年2月28日。-This is a friendly arm of the core board micro2440 board schematic, update time is February 28, 2009.

c 51编程的一个教训，抛出一个范例是为了然大家吸取教训。-programming a lesson dished out an example to everyone ran to learn.

密码锁的设计,单片机初学者必须程序,适用于proteus-Locks design, single-chip microcomputer program for beginners to be applicable to proteus

用凌阳16位单片机测试输入波形的频率，动态刷新显示-Sunplus 16-bit single-chip microcomputer used to test the frequency of input waveform, dynamic refresh display

报警电路 单片机控制的自动报警器 C程序和汇编编写-Single-chip control circuit alarm alarm automatic compilation of procedures and the preparation of C

keil C51 H－Test事例-H-Test case

CCS编译器下PIC16F887使用示例-CCS compiler to use the sample under the PIC16F887