Realize single

写eeprom的c语言程序，在msp430单片机x1系列上调试通过-EEPROM write the c language program, in the MSP430 family of single-chip debugging through x1

这是几年前我写的，自动识别RS485和RS232接线极性、自动检测波特率、自动匹配协议的云台控制软件，只是当时我还没用C写-This is a few years ago I wrote, and automatic identification RS485 and RS232 wiring polarity, automatically detects the baud rate, auto-matching agreement Yuntai control software, but I did not then use C to write

识别语音的C代码! 还有教程说明.大家自己看看吧!-Identification of the C code voice! There are tutorials that. Everyone could see for himself now!

这是一个在两台pc机之间通过串口传输文件的汇编程序-This is one of the two PCs via serial port to transfer files to the assembler

用2407控制三相交流电机的程序,c语言-with 2,407 three-phase AC motor control procedures, language c

USB PDIUSB12D C语言驱动程序库1-USB PDIUSB12D C language for a driver

masm old fargon 2 to do asmbly code

模拟银行卡取款操作，银行卡号为8位，能够进行查询、取款、存款、修改密码等操作。查询时需要输入密码，密码为6位。当密码位数和相应位都符合时，显示卡内余额，否则密码三次错误，结束操作。取款时也需要输入密码，密码为6位。当密码位数和相应位都符合时，显示现有余额，输入取款金额，操作结束显示所剩金额，否则密码三次错误，结束操作。限制每天总共可取的金额 ，若违规给出相应的警告。取款操作时输入取款金额 ，操作结束，显示卡内余额，输入密码时，不显示真实值，修改密码时显示真实值。-simulated bank teller card operation, a registered member of the eight to conduct inquiries, withdrawals, deposits, change passwords operation. Inquiries need to enter a password, the password to six. When the median and the corresponding password-meet, showed the card balance, otherwise the wrong password three times, the end of operation. Teller also need to enter the password, the password to six. When the median and password are consistent with the corresponding position, shows that the existing balance of the amount imported withdrawals, the remaining operation ended shows the amount, otherwise the wrong password three times, the end of operation. Limit daily total amount of desirable, if irregularities are given corresponding warning. ATM withdrawals

使用74164连接8行2列键盘的行线，74165连接键盘的列线，编写扫描键盘，包括C和汇编程序-74164 connect using 8 line 2 keyboard line, out of 74,165 lines to connect the keyboard, the preparation of scanning the keyboard, including C and assembler

6221mada.asm.........遥控电机程序， 按遥控器0-9步进电机正转0-9步，按遥控器11-19步进电器分别反转 dianji.asm..........步进电机正转，反转各3圈 keyd.asm............步进电机控制程序p3.2正转,p3.3反转,p3.4停止 步进电机接p1.0p1.1p1.2p1.3 abdian.asm...........步进电机正反快慢转！ madatest.asb.............步进电机测试，最简单的转圈程序 -6221mada.asm ......... electric remote control procedures, in accordance with the remote control stepper motors 0-9 to 0-9 are step-by-step, 11-19 step by remote control electrical inversion, respectively dianji.asm ... stepper motor is ....... turn, reversal of the 3 lap keyd.asm ............ stepper motor control program to p3.2 is, p3.3 inversion, p3.4 stepper motor to stop p1.0p1.1p1.2p1.3 abdian.asm ........... then stepping motor speed to the pros and cons! stepper motor test madatest.asb ............., the simplest circular motion the procedures