一种很好的用单片机控制步进电机的程序，用汇编语言编写。...

天行健，君子以自强不息  请点击左侧文件开始预览 ！预览只提供20%的代码片段，完整代码需下载后查看 加载中 侵权举报

外部中断与Timer中断同时存在的实验 （单片机）-External interrupt Timer Interrupt-exist with the experimental

用汇编语言编程，环境为keilC开发环境，显示温度-Using assembly language programming, the environment keilC development environment, shows that the temperature

这个程序我花了好久才写出来的,非常的好,它可以产生很高性能的三角波,一般程序不易产生如此好的波形.-this process I have spent a long time before the writing, very good, and it can produce a very high-performance triangular wave, the general procedures have not been so good waveform.

这个运用了win32中的一些内容 由原来的单一的颜色不断换成不同颜色-win32 the use of some elements of the original single color constantly replaced by the different colors

设计一种自动洗衣机的程序控制器，在启动后先进水，等到达高水位后，启动洗衣马达转动4min，如在洗衣过程中发现水位低于高水位，则停止洗衣马达转动并报警，并在水位到达高水位后再次启动马达。洗衣结束后则启动排水开关，待水位到达低水位后，则启动脱水马达，转动2min。如此重复三次，要求在每一动作之间有2s的间隔。 高水位，低水位为水位传感器，用两个开关模拟，当水位高于高水位或低于低水位时，两个开关的状态分别为0 。启动开关用一个开关表示。进水、排水、洗衣马达、脱水马达及报警分别用一个发光二极管表示。本实验只需用可编程并行接口电路的A口。其硬件接口如下图所示。也可采用可编程逻辑器件进行设计。 -Design of an automatic washing process controller, after commencement of advanced water, and so on to reach the high water mark, start laundry motor rotation 4min, such as in laundry water level lower than that found during the high water mark, then the motor stops rotating laundry and alarm, and the the water level reaches the high water mark again to start the motor. Laundry is started after the end of the drainage switch, when the water level reaches the low water level, then start the dehydration motors, rotating 2min. Repeat three times, each action requires the interval between the 2s. High water, low water level as water level sensors, with two analog switches, when the water

足球比赛的分组淘汰制以及比赛过程和比赛结果的运行和现实-Football knockout competition, as well as group games and competitions during the operation and practical results

VB写的一个ASM汇编转机器码的代码,很方便的把汇编语言转成机器码操作-vb asmtohex

;功能：输入num个两位数据(00~99)，显示求出的和与平均数;说明：以英文输入法,输入格式为98,95,90,96,94…,每次两位，最后以回车结束;注意：输入成绩的个数超过或者少于num定义的个数，程序均会提示出错信息 ;开发平台：emu8086 V4.05;编写：LS 2014年1月3日

这是12864 带字库的显示子程序 reset 是初始屏幕的 display 是显示数据的 input是输入地址的指令-This is the 12864 with reset font display subroutine is the initial screen display is to show the data input is the input address command