达拉斯DS18B20的温度数值计算程序。

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

430的SD16模块扩展到20bit采样精度的范例-430 extended to the SD16 module 20bit sampling accuracy of the sample

三个点温度进行监视；任意一个测温点大于设定温度报警提示-3-point temperature monitoring any point of a temperature greater than the set temperature alarm

Kicad的中文入门手册，才翻译的，国外的开源PCB绘图软件-Chinese Primer Kicad only the translation of foreign open-source PCB drawing software

实现基于PIC25j10单片机，实现对HSM－20G温湿度模块，对换境数据的采集，给压缩包包含了所用到芯片的DATASHEET以及原代码-PIC25j10-based microcontroller, the realization of HSM-20G module temperature and humidity on the Habitat for data collection, to the compressed packet contains the chip DATASHEET used, as well as the original code

LT_1B msp430开发板例子程序－TA_13

AT mega88 A/D转换的实现 采用的是外部中断进行控制A/D转换-AT mega88 A/D conversion is achieved using an external interrupt to control A/D conversion

AVR单片机的RS232通信演示程序，采用八兆晶振的传输字符串函数。-AVR RS232 communication demo program using eight Katherine crystal transmission string function.

C8051F的步进电机驱动程序。控制中的经典问题，值得一看-C8051F stepper motor driver. Control of the classic, eye-catcher

P89C669存储实例: 说明： 1. inc 文件夹 是关于P89C669的头文件，在使用下面两个例子前，请首先将头文件拷到 ..KeilC51INC下. 2. Rom 文件夹 是关于P89C669的程序空间使用的例子，说明怎样利用大于64KB的程序空间。 3. Ram 文件夹 是关于P89C669的数据空间使用的例子，说明怎样在各个数据空间定义变量。 -P89C669 storage examples: Note: 1. Inc folder is on the first P89C669 documents, in the use of the following two examples, please first Kaodao header files .. KeilC51INC under .2. Rom folder P89C669 procedures on space use example of how to make use of the procedure is greater than 64KB of space. 3. Ram folder P89C669 data on space use examples to illustrate how the definition of data space in all variables.