Communications routines 485 for them to learn from the reference. Communications...

采用美国adi公司的bf系列，基于bf533的ez-kit平台的mmc和sd的读写功能的代码-Adoption of the United States adi

串行口uart-rs232不带缓冲器区的显示模块，望大家给与意见-Uart-rs232 serial port with no buffer zone display module, hope you give advice

本程序是针对特定GPS接收机--JAVAD公司的legacy的一个应用，用来收取标准的NMEA-1083GGA信息或JPS格式（JAVAD公司的特有GPS信息格式）的{RT，PO}信息，并统计数据大小与经历时间。本程序用VC6.0+串口控件MSComm实现，其中关于如何在数据长度不定的情况下实现数据帧的同步的方法可以借鉴到其它串口数据采集的应用之中，具备一定的实用价值-this program is targeted at specific GPS receiver-- JAVAD the legacy of an application, used to collect standard NMEA- 1083GGA information or JPS format (JAVAD company"s unique GPS information format) (RT, PO) information and statistical data on the size and duration. The procedures used VC6.0 Serial MSComm control, on how volatile the data length of the data frame synchronization method can draw on to other serial data acquisition applications, to have some practical value

getmywish使用的usb注意：由于用到多串口控制，需要在收到数据时确定是哪个串口来的数据。 下面是串口事件处理函数代码： -getmywish use usb Note : As used Multiport Serial control, the receipt of necessary data to determine which of the serial data. Below are the serial code incident handling functions :

C51单片机串行口中断服务程序,good-C51 single-chip serial port interrupt service routine, good

mscomm的控件，基于VB，C++ 或API的控件。-MSComm control, based on the VB, C++ or API controls.

串行口是计算机一种常用的接口，具有连接线少，通讯简单，得到广泛的使用。常用的串口是RS-232-C接口(又称EIA RS-232-C)它是在1970年由美国电子工业协会(EIA)联合贝尔系统、调制解调器厂家及计算机终端生产厂家共同制定的用于串行通讯的标准。它的全名是"数据终端设备(DTE)和数据通讯设备(DCE)之间串行二进制数据交换接口技术标准"该标准规定采用一个25个脚的DB25连接器，对连接器的每个引脚的信号内容加以规定，还对各种信号的电平加以规定。传输距离在码元畸变小于4%的情况下，传输电缆长度应为50英尺。 　　Linux操作系统从一开始就对串行口提供了很好的支持，本文就Linux下的串行口通讯编程进行简单的介绍.-computer serial port is a common interface, with connecting lines, simple communications, to be widely used. It is commonly used serial RS-232-C interface (also known as the EIA RS-232-C) it is in 1970 by the American Electronics Industry Association (EIA) Joint Bell System, a modem manufacturers and computer terminal manufacturers developed for serial communication standards. Its full title is "data terminal equipment (DTE) and data communications equipment (DCE) between serial binary data exchange interface technology standards," the use of a standard 25 feet to the DB25 connector, the connector pin of each signal content requirements, but also the right signal--

MSComm32.ocx串口通信程序。测试时不要用虚拟串口，直接将串口2引脚与3引脚短接。-MSComm32.ocx serial communication program. Not to test with virtual serial port, serial port directly to 2-pin and 3 pin shorted.

A/D转换－数据采集实验 * * A/D转换数据采集程序source file * * 运行步骤：1.在平台板的8位AD通道选择开关上 选定通道号 * * 2.程序运行后，转动电位器，观测数据的变化 -A/D converter-experimental data acquisition** A/D converter data acquisition program source file** Run steps : 1. The platform board eight AD channel selection switch on the selected channel,** 2. Running after turning Potentiometers, observational data changes

注释 用VC++编写USB接口通信程序 -prepared USB Communication Program prepared by VC USB Communication Program