Debug adopted 89S51

aduc834 iic 通讯 aduc834 iic 通讯-aduc834 iic communications communications aduc834 iic

ds18b20的驱动程序，汇编语言编的，由两位数码管显示，程序已经在AT89C51上调通了，附带proteus仿真文件。-DS18B20 driver assembly language made by the two digital display, the program has had a rise in the AT89C51, incidental Proteus simulation file.

关于红外遥控智能小车的汇编程序，简洁易懂，希望大家都来看啊！-Smart car on the infrared remote control of the compilation process easier to understand, ah, we want everyone to look at!

电动车从起跑线出发（车体不得超过起跑线），沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需立即发出声光指示信息，并实时存储、显示在“直道区”检测到的薄铁片数目。 （2）电动车到达B点以后进入“弯道区”，沿圆弧引导线到达C点（也可脱离圆弧引导线到达C点）。C点下埋有边长为15cm的正方形薄铁片，要求电动车到达C点检测到薄铁片后在C点处停车5秒，停车期间发出断续的声光信息。 （3）电动车在光源的引导下，通过障碍区进入停车区并到达车库。电动车必须在两个障碍物之间通过且不得与其接触。 （4）电动车完成上述任务后应立即停车，但全程行驶时间不能大于90秒，行驶时间达到90秒时必须立即自动停车。 -err

基于DSP2812的电机的控制程序源代码：包括永磁同步电机，感应电机，无刷电机，开关磁阻电机，还附带9组测试程序-electromotor control dased on DSP2812

一个汇编的学籍管理程序-A compilation of the school management procedures

EEPROM局部抄写软件,可以任意设置地址,抄写一段数据,数据由母片提供.-EEPROM partial copying software, can set up addresses, copying a section of data, data provided by the master.

交通灯控制器 请注意: 本例的各个源描述的编译顺序应该是: 64_tlc.vhd 64_test_vector.vhd-Traffic Light Controller Please note: This case is described in various sources to compile the order should be: 64_tlc.vhd 64_test_vector.vhd

MCD1实战一,点亮一个LED并持续3秒后熄灭 该实战的目的作为学习和应用MCD1在线调试工具套件，进行项目的软件和硬件 联合调试的范例程序，也就是当做一个用户程序实例，而演示板暂时充当用户电 路的角色。这样就构成了一个软件、硬件齐全的自制项目模拟环境。 本程序实现的功能是，把端口RC的8条引脚全部设置为输出模式，并从RC0输出高电平 从而点亮RC0口的一个LED,持续3秒后LED熄灭. 该程序可用于PIC16F87X(A)所有系列-MCD1 real one, to light a LED and continuously put out 3 seconds after the real purpose for learning and application debugging MCD1 online suite of tools to carry out the project software and hardware examples of joint commissioning procedures, that is, as a user instance, and the demonstration user circuit board to serve as a temporary role. This constitutes a software, hardware, a full range of home-made simulation environment projects. Realize the function of this procedure is that the 8-port RC pin all set to output mode and high output from the RC0 so I RC0 a lit LED, continuous 3 seconds after the LED goes out. The program can be used to PIC16F87X ( A) All Series

hex 转 二进制-hex binary switch