凌阳单片机解码SAA3010T（通用无线遥控） sunplus IDE(集成开发环境）...

这是ATMEL公司，的AT9200的LOADE程序让你们感受一精简指令集的冲击-This is ATMEL Corporation, the AT9200 LOADE the procedures so that you feel a RISC impact

也用到了温度PID控制,和我门的不同是采用D/A输出控制量的.主要由温度采样--->温度滤波子程序--->温度线性化----->温度设定值等模块组成.-also uses a PID temperature control, and my door is different D/A output volume control. By sampling temperature--- gt; Temperature filter subroutine-- gt; Temperature linear----- gt; The temperature setpoint and other modules .

使用proteus和Keil联调SCM51,此例程精讲了P0口匚用-The use of proteus and Keil FBI SCM51, this routine I精讲the匚with P0

遥控数字钟应用程序，应用于多种数字钟接口，可以遥控设备，省力。自制LED电子钟在很多电子报刊杂志上都可以见到，但大多数在断电后都要重新设置时间等 参数，给使用带来很多不便。也有用后备电池作为备用电源的，但往往体积较大。本文介绍 的LED电子钟克服了以往的弊端，而且采用了家电通用的红外遥控器进行控制，方便使用。 有一路闹铃输出，可以通过遥控器设置闹铃时间及允许与否。-digital clock remote control applications, digital clock used in a variety of interface, remote-control equipment, effort. Homemade LED electronic bell in many electronic newspapers and magazines can all, but most of the power outages after the re setup time and other parameters to use in many ways. Also useful as a standby battery backup power, but often larger. This paper introduces the LED electronic clock to overcome the shortcomings of the past, and the use of common household appliances infrared remote control, and ease of use. A way Alarms output, the remote control can set the alarm time and allow it or not.

长沙理工自己的实验程序，从最基础的到高深一点的，都有。不过实验箱是我们学长自己设计的，其它的箱子要调试的话还需相应改动-Changsha Institute of Technology

这是我在我们公司做的C51加油单片机程序-in our company do C51 microcontroller refueling procedures

1602 液晶显示 电子表程序时 分 秒 使用的是新华龙单片机 100脚 的 -1602 liquid crystal display digital watches every minute procedure using a new single-chip 100-pin of Hualong

语音温度计输出当前摄氏度，如果超出一定的范围会报警。-Degrees Celsius thermometer voice output current, if the scope will go beyond a certain alarm.

注:protel电路图 1.INPUT12为高压气压和低压压传感器输入端. 2.OUTPUT为充气输出控制端. 3.当高低压有接地信号时,电机正转,气阀打开. 4.INPUT2低气压时有信号时,充气OUTPUT输出,充气电机转. 5.RS1与RS2是调节阀门距离用地 6.RS3是与气阀电机同步时,是气阀电机的转动圈数传感器. 7.RS4是调节延时时间用地-Note: protel circuit 1.INPUT12 and low-voltage high-pressure pneumatic pressure sensor input. 2.OUTPUT output control for the inflated side. 3. When the high and low pressure have a grounding signal when the motor is transferred, the valve opens. 4.INPUT2 low pressure when there is signal output OUTPUT inflatable, inflatable motor switch. 5.RS1 and RS2 is the regulator valve from the land 6.RS3 synchronous motor with the valve, the valve motor is rotating circle the number of sensors. 7.RS4 delay time to regulate land

DS1302的C语言程序例子-DS1302 C language program examples