This a remote control for the use of embedded devices developed by a Chinese Pin...

基于IAR平台STM32处理器实现鼠标、键盘类设备的源代码-STM32 processor-based platform to achieve IAR mouse, keyboard class device" s source code

PROFIBUS_dp设备接口的开发与应用1（终）.rar-PROFIBUS_dp Device Interface Development and Application of a (final). Rar

应用背景本设计的数字音乐盒以AT89C51单片机为核心，用C语言编写。利用单片机的定时器产生不同频率的声波，由I/O口输出，继而启动蜂鸣器发出音乐。通过外部中断进行歌曲切换，通过按键控制播放/暂停。实现几首乐谱的循环播放，同时LCD 1602显示自定义字符“♫”、正在播放曲谱编号、曲谱总数、曲谱名滚动关键技术/*********************可控LCD数字音乐盒***************************** http://wenku.baidu.com/view/41f87df4daef5ef7ba0d3c77?fr=prin 标题：Music Box.c 功能：实现几首乐谱的循环播放，同时LCD1602显示正在播放乐谱序号、 乐谱总数、乐谱名滚动；可通过按键控制启停、选曲。 说明：MCU为AT89C51，编译环境为Keil C51 uV4，与LCD1602连接关系为 { RS——P2.0， RW——P2.1, E——P2.2， P2——D0~D7 } ╔╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╦╗ ╠ 按键   端口                     操作  ╠ ╠---------------------------------------------╠ ╠ K1     P1.0               播放/暂停 ╠ ╠ K2     P3.2 （中断）     上一曲  ╠ ╠ K3     P3.3

DNW0.50L软件的源代码，目前的最新版本，在0.50A的基础上增加了UBOOT选项。-DNW0.50L software source code, the current latest version 0.50A basis in an increase of UBOOT options.

遥控器解码和1602驱动程序，一个用c写的源代码。-Remote control decoding and 1602 driver, one with c source code to write.

at91sam7s64的一个应用.使用ads1.2编译器,实现usb口的通讯功能.-at91sam7s64 of an application. Use ads1.2 compiler, I realize usb communication capabilities.

周立功　2410　开发包，不错的代码，推荐！-Week Ligong 2410 development kit, a good code, recommend!

自动升降电梯控制器设计 要求： 设计一个6层楼的电梯控制器。 该控制器可控制电梯完成6层楼的载客服而且遵循方向优先原则，并能响应提前关门延时关门，并具有超载报警和故障报警； 同时指示电梯运行情况和电梯内外请求信息。-Auto-Lift elevator controller design requirements: design of a six-story elevator controller. The controller can control the completion of six-story elevator containing the principle of giving priority customer service, and follow the directions, and can respond to close ahead of schedule delay closing, and has overload alarm and fault alarm also instructed the elevator and elevator operation request information both inside and outside.

液晶屏1604的一个驱动程序，里面有proteus的仿真电路图，代码很省。-screen of a 1,604 drivers, there are lic circuit simulation, the code was very frugal.

用ISD1700来实现读温度，比如27.5摄氏度，先分段录制声音：1,2,3,4,5,6,7,8,9,十，点，温度，摄氏度。读27.5摄氏度时，再分段找地址，读出相应的数-Reading used to achieve ISD1700 temperature, such as 27.5 degrees Celsius, the first sub-recording the voices of: 1,2,3,4,5,6,7,8,9, ten, point, temperature, degrees Celsius. Reading of 27.5 degrees Celsius, then find a sub-address, read out the corresponding number of