是由MSP430 单片机控制实现的 多功能语音的录音和放音系统 可以由外接功放和其他语音设备来实现 其功能...

健身器械面板显示程序，可以显示时间，距离，速度等，并具有三个按键进行相应的操作-fitness equipment panel display program can demonstrate that time, distance, speed, and with three buttons for the appropriate operating

能实现多功能。既可做倒计时秒表,又可进行定时，还可以通过扩展完成其他功能，而且功能的相互转换也十分简单-To achieve multi-functional. Can do the countdown stopwatch, but also to timing, but also by extending the completion of other functions, and inter-conversion functions is also very simple and

此为单片机的一个电子钟程序，希望对大家有帮助-This is an electronic bell SCM procedures, in the hope that everyone has to help

MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to

简易数字电压表可以测量0-5V范围的8路电压值，并在4位LED数码管上轮流显示或单路选择显示。-Simple digital voltage meter can measure the range of 0-5V Voltage road 8, and 4 digital tube LED display on a rotational basis or choose to display a single road.

用C写的I2C总线EEPROM读写程序，在MSP430＋AT24C64～512平台上验证通过。对其他处理器只需简单修改即可使用。-C write I2C EEPROM read and write procedures, the AT24C64 MSP430+ ~ 512 platform validation through. The only other processor can use a simple amendment.

这里是51单片机的一些子程序，包括12864LCD的显示，ds18b20的显示，zlg7290的控制。-Here are some of the subroutines 51 MCU, including the 12864LCD display, ds18b20 display, zlg7290 control.

ARM7――lpc2148forSD卡的读写控制-ARM7- lpc2148forSD card read and write control

利用LABview做的解无线传感器节点的包的数据的程序-Does the solution make use of Labview wireless sensor nodes process data packets

一些单片机C程序，希望对初学者有一定作用-Some single-chip C program, and they hope to have a role beginners