ARM9下的UCOS原代码

ucosII2.8,最新版本强烈推荐不要客气共同学习-ucosII2.8, the latest version strongly recommend learning together do not mention it

介绍了L C ö O S 2Ê 在TM S320VC5402 上的移植以及在移植过程中的一些注意事项, 给出一些关键的实现代码,并在移植的基础上给出了改进堆栈设计以减少对内存需求的方法。-introduced ouml C L O S 2Ecirc TM HPI in the transplant process and the transplantation of some note, is the realization of some of the key code, and the transplant is given on the basis of an improved stack design to reduce memory requirements methods.

LM3S_uCOS2 for 485总线源代码-LM3S_uCOS2 for 485 bus source code

UCOS在44B0的移植，需要一点小修改-UCOS in 44B0 transplant and will need some minor edits

S3C44B0下的ucos程序。并包含了udp/ip网络通讯同能。(S3C44B0 under the procedures OUT. And contains udp/ip network communication can be the same.)

说明：  本人是刚刚毕业的学生，毕业设计时的题目是数字示波器，本示波器是用基于LPC2290ARM和UCOS2操作系统设计的，这是原代码，UCOS操作系统的移植代码由于公司原因没有上传！(I am a recently graduated student, graduated from the design of the subject is digital oscilloscope, the oscilloscope is LPC2290ARM and UCOS2 based operating system designed, which is the original code, UCOS operating system code as a result of the company the reasons for transplantation did not upload!)

SC28L198是一个带有8个全双工异步通道UART的芯片，每个UART通道的接收器和发送器都拥有16字节深度的FIFO。芯片的每个UART通道除了基本的异步通信功能外，还可实现软件流控制（in-band flow control）、硬件流控制（out-of-band flow control）、以及多点模式（唤醒模式或RS-485模式）等，同时每个UART都有4个外扩的I/O引脚，每个外扩I/O引脚都为功能复用。 本资料包含完整测试程序，应用文档，电路原理图及PPT演示文档等。(SC28L198 is a full-duplex asynchronous channels with 8 chip UART, each UART channel receiver and transmitter have 16-byte deep FIFO. Each UART channel chip, the asynchronous communication addition to the basic functions, but also for software flow control (in-band flow control), hardware flow control (out-of-band flow control), as well as multi-point mode (wake-up mode, or RS-485 mode), etc., and each UART has a 4 outer expansion of the I/O pins, each outer expansion I/O pins are as functional reuse. This information includes a complete test program, application documents, the circuit schematic diagram and PPT presentation documentation.)

KEIL 下的UCOSII移植，里面有LED的点灯，点灯是需要按一下按LED灯亮一下，还有串口，不过波特率不准，只实现接收进入中断，其实就是完成了中断进入、信号量创建，对初学者十分有用。此例子用的是KEIL公司的MCB2300开发板，和英蓓特的LPC2300一样，原理图可以在KEIL公司官网上下到。-KEIL under UCOSII transplantation, there are LED

proteus仿真、ARM7、ucos-II系统-ucos-II code of using proteus and ARM7

可以在ARM嵌入式单片机上运行的uCOS源程序，可以用于移植。-Single-chip ARM embedded in running uCOS source, can be used for transplantation.