登录
首页 » SCM » zlg 的easyarm easyarm

zlg 的easyarm easyarm

于 2022-08-17 发布 文件大小:960.27 kB
0 162
下载积分: 2 下载次数: 1

代码说明:

zlg 的easyarm easyarm-ZLG

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 485端口抄表程序,通过485端口进行电表抄写
    485端口抄表程序,通过485端口进行电表抄写-485-port meter-reading program, through the 485 meter port copying
    2022-03-07 12:41:21下载
    积分:1
  • 课程设计做的基本程序,可实现串口通信,定时,键盘扫描等功能!...
    课程设计做的基本程序,可实现串口通信,定时,键盘扫描等功能!-Curriculum design to do the basic procedures can realize serial communication, timing, keyboard scanning and other functions!
    2023-04-02 17:55:02下载
    积分:1
  • 使用PIC12C508509的例程:用PIC12C508509 控制一个步进电机源程序,用PIC12C508A 控制模型源程序和用PIC12C509 控制LED...
    使用PIC12C508509的例程:用PIC12C508509 控制一个步进电机源程序,用PIC12C508A 控制模型源程序和用PIC12C509 控制LED。-an example program about PIC12C508509: use PIC12C508509to control stepping motor, use PIC12C508A controlling model source and PIC12C509 control LED
    2022-03-03 16:44:37下载
    积分:1
  • 这是一个1602液晶的显示程序,基于51单片机,已实验成功
    这是一个1602液晶的显示程序,基于51单片机,已实验成功-This is a 1602 LCD display procedures, based on 51 single-chip, has conducted successful experiments in
    2022-03-03 23:34:22下载
    积分:1
  • c51的资料主要在单片机中的应用,是很好的工作手册
    c51的资料主要在单片机中的应用,是很好的工作手册-information mainly in the C51 single-chip application, is a good manual
    2022-07-16 20:10:35下载
    积分:1
  • ARM采用的是LPC2210,液晶采用TFT的。源码为C。在SMATR2210上使用过。...
    ARM采用的是LPC2210,液晶采用TFT的。源码为C。在SMATR2210上使用过。-ARM is based on LPC2210, the use of TFT LCD
    2022-08-07 20:00:42下载
    积分:1
  • 控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序....
    控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序.-Control motor movement, G code program, if the G code is not clear, please understand G code, and then look at the procedures.
    2022-05-18 13:24:10下载
    积分:1
  • MCS
    MCS-51单片机有5个中断源,其中两个是由-INT0、-INT1引脚输入的外部中断源;另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式,即下降沿引起中断或低电平引起中断。当编程TCON中的ITi(i=0、1)为1时,则引起触发的方式为边沿触发方式,反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制,即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to
    2023-07-06 00:00:03下载
    积分:1
  • MSP430液晶控制程序,可以控制一般的12864液晶显示屏,短小,配合8M赫兹时钟频率...
    MSP430液晶控制程序,可以控制一般的12864液晶显示屏,短小,配合8M赫兹时钟频率-MSP430 LCD control procedures to control the general 12864 LCD screen, short, with 8M Hz clock frequency
    2022-02-05 21:56:38下载
    积分:1
  • 单片机
    基于KeilC 平台的单片机源码,适用于AT89ls52,程序通过中断方式查询按键的输入,I/O口接入单独按键。-Microcontroller-based platform KeilC source for AT89ls52, procedure interrupt input query keys, I/O port access to a separate button.
    2022-06-01 10:28:14下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载