这个范例说明如何使用8051 的Port 1连接到四颗七段显示器，PORT 0的低4位分别控制这四颗共阳七段显示器，让四颗共阳七段显示器使用扫描的方式轮流...

DDS芯片AD9851的程序，keil编写，AD9851接成并行接口-err

步进电机的驱动程序,按3个速度段,让步进电机跑的跟精确-Stepper motor driver, according to the speed of paragraph 3, concessions into the motor running with the precision

介绍了ATMEGA128的AD使用，很详细，值得一砍，不过是E文的-ATMEGA128 introduced the use of the AD, in great detail, it is worth a cut, but the text is E.

急救车与交通灯）（1）南北与东西方向，每个方面由红黄绿三个灯控制（2）南北向：　红（30秒），黄（5秒），绿（25秒）　　　东西向： 红（35秒），黄（5秒），绿（25秒）　　　上述基本参数可以根据实际情况自行调整，灯的变化规律与实际路口规律相同，绿灯在最后5秒钟时，黄灯亮，然后红灯亮，不允许两个方面同时亮绿灯。（3）绿灯的时间显示在数码管上进行显示。（4）可以通过一个开关控制，当开关信号为0时，整个交通灯全灭提高要求：（1）设计一个紧急控制开关信号，当紧急开关信号为1时，两个方向的灯全为红灯。紧急开关撤消后，按照开关按下之前的状态继续运行（其参数要保存）。（2）设计一个夜间行车开关，当开关按下后，两个方向都只有黄灯闪烁，其它灯熄灭。（3）设计两个方向的亮时时间可调。-emergency vehicles and traffic lights) (1) North and South and east-west direction, each with three yellow-green from red lights control (2) to the north and south : red (30 seconds), yellow (5 seconds), Green (25 seconds) to things : red (35 seconds), yellow (5 seconds) Green (25 seconds) above basic parameters can be adjusted to the actual situation, the light changes with the actual law of the same intersection, the green light in the final five seconds, the yellow light is on, and then a red light, bright, not two fronts simultaneously bright green. (3) the green light at the time displayed on the digital display control. (4) can be controlled by a

用单片机实现电子钟功能，供初学者学习单片机使用-Electronic bell with MCU functions, for beginners to learn to use single-chip microcomputer

单片机与PC键盘的程序-MCU and the procedures PC keyboard

无线传感器节点源代码，采用ATMEGA128控制CC1000.-The source code for wireless sensor nodes, using ATMEGA128 control of CC1000.

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

准确，快速，方便地获得温度在现代企事业单位，厂房车间和家庭中有着越来越重要的意义。本文设计了一套基于MSC51单片机的温度采集系统。应用该系统可以即时、准确地获得两路温度参数（可扩展至256路），测温范围达0~125C，参数精确至0.25C，并可以现场控制欲采集的指定传感器的温度参数，通过数码管显示出来，通过RS232接口可连接至计算机，并通过监控软件观察实时数据和波形。该系统具有易扩展、精度高、成本低等特点，适宜现场监控，实验室，家庭等对温度有要求的场所。-Accurate, rapid and easy access to the temperature in the modern enterprises, plant has a home workshop and more and more important. This article has designed a single chip MSC51-based temperature acquisition system. Application of the system can be immediate, accurate access to two temperature parameters (can be expanded to 256 road), temperature range of 0 ~ 125C, precise parameters to 0.25C, and can be collected at the scene To control the temperature of the sensor parameters specified by the digital tube shown through RS232 interface can be connected to the computer and monitoring software through real-time data and waveform observation. The system is easy to expand with high precision, low cost, and suitable for field monitoring, laboratory, on the home

是一个关于速度开环控制的空间矢量交流调速程序-a c programe for an open loop AC motor speed control. Method: space vector pulse width module