对电网参数的测量程序，可测量多个参数，包括LED显示和键盘中断程序...

A/D转换器ADC0832驱动程序，该程序属于A/D的基础程序，可以调用该函数来实现A/D转换-A/D converter ADC0832-driven program, which belongs to A/D based program, you can call this function to achieve the A/D converter

在达盛实验箱下的lcd单片机显示，两行国标汉字，爱好者可以好好学习一下-Tat Shing lcd under experimental single-chip boxes show two lines of Chinese characters GB, fans can learn about

用485实现单片机之间的串行通信。 主机部分发送从机地址，等待从机响应，从机准备好就发数据,发完就接收从机的响应，接受成功就跳出循环，否则重发。-MCU with 485 Serial Communication between. Host of this address from the plane, waiting for the response from the plane, from the plane ready to discuss the data, finished on the reception of the response from the plane. set aside for recycling success, otherwise re-issued.

这是参加电子设计大赛时的作品：红外遥控小车：用红外线通过一块AT89S52单片机发射信号即编码，并用红外接收头接收信号；接着再用另一块AT89S52单片机对红外发射出的信号编码进行解码，最后再用一块AT89S52单片机用解码所得码值编写程序后驱动步进电机。步进机功能启动后不仅能使受控小车向前后左右四个方向前进和转弯，而且还能控制小车再地上转动并留下方形或圆形等形状。-This is the time to participate in Electronic Design Contest works: infrared remote control car: Using infrared transmission signal through an AT89S52 microcontroller that is encoded and used infrared receiver to receive the first signal and then using the other an infrared emitting MCU AT89S52 code and decode the signal and finally an AT89S52 microcontroller then proceeds with the decoding key value of the preparation of procedures to drive a stepper motor. Stepper machine function activated not only make the car forward in a controlled direction and after about four turns, but also to control the car and then turned and left the ground such as square or round shapes.

主要用到了PID算法控制温度,显示采用动态扫描.输出可调节占空比的脉冲控制加热器-mainly used to control the temperature PID algorithm, shows that using dynamic scanning. Output adjustable pulse duty cycle control of the heater

c51单片机实验程序代码--流水灯、时钟、液晶驱动，串口异步通信、AD、DA、ROM 扩展、IO扩展等等，附原理图，对初学者很有帮助。-C51 single-chip experimental procedure code- water lights, clock, LCD driver, serial asynchronous communication, AD, DA, ROM expansion, IO expansion and so on, with schematic diagram, useful for beginners.

8051F330 pid ad舵机模拟串口数码显示-8051F330 pid adservo scidispaly

本程序实现msp430通过CS8900A与以太网的通信-This procedure to achieve msp430 through CS8900A and Ethernet communications

将数0000-9999用数码管依次循序显示 实验步骤: 1.打开伟福V3.20,创建一新文件 2.编写源代码 3.保存文件,文件名后缀为.asm 4.编译程序 5.打开Easy 51Pro v2.0将程序写进实验板-Experimental steps: 1. Open-wei Fu V3.20, create a new document 2. To prepare the source code 3. Save the file, the file name suffix to. Asm 4. Compiler 5. Easy 51Pro v2.0 to open the program into the board

用于51系列单片机的串口程序源码-51 for the single-chip Serial procedures FOSS