无线解码程序，是用于多种无线报警主机的解码

CH375 主机文件系统接口(支持FAT12/FAT16) MCS-51单片机C语言的U盘文件读写示例程序-CH375 host file system interface (support FAT12/FAT16) MCS-51 single-chip U of C language sample programs to read and write disk files

ds2482-100是IIC协议转1-wire协议的接口芯片。本程序包利用ds2482-100操作温度传感器ds18s20。注意：ds18s20初始化后温度值为85摄氏度，必须多读几次温度以便其显示稳定。另外，文件中包含的一些头文件可以顾名思义，都是比较通用的（如IIC软件包），为节省篇幅，没有包含进来。请在 编译时自己根据接口函数添加。-ds2482-100 is IIC agreement to 1-wire agreement interface chip. The packages use ds2482-100 ds18s20 operating temperature sensor. Note : After initialization ds18s20 temperature of 85 degrees Celsius, to be read several times the temperature to show its stability. Also, the document contains a number of header files can name suggests, are relatively common (eg IIC package), To save space, are not included come. Please compiled under its own interface function was added.

AVR开发工具-ISP下载电缆的PCB图 PonyProgPCB-AVR development tools-download cable ISP PCB plans PonyProgPCB

单片机485 CAN-bus-RS485CAN.pdf-Single-chip 485 CAN-bus-RS485CAN.pdf

用VHDL实现8位的单片机！里面 有开发过程和代码阿！很详细的哦-using VHDL eight of SCM! Inside the development process and code Ah! Detailed oh

MC9S08GB/GT 串口监控程序源码-Serial Port Monitor MC9S08GB/GT source

给出一种利用单片机通用I/O 口扩展串行通信的方法.-Given a general-purpose use of single-chip I/O port expansion method of serial communication.

本程序有友善之臂提供，为2440开发板的led示例程序，请使用ADS编译。-This procedure has the arm of a friendly offer for the 2440 sample development board led the process, use the ADS compiler.

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

网上搜集的IDE控制的c51程序，可以研究一下。-online collection of IDE control of the decoder procedure could look into.