s3c4510 uclinux sample

L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是：工作电压高，最高工作电压可达46V；输出电流大，瞬间峰值电流可达3A，持续工作电流为2A；额定功率25W。内含两个H桥的高电压大电流全桥式驱动器，可以用来驱动直流电动机和步进电动机、继电器线圈等感性负载；采用标准逻辑电平信号控制；具有两个使能控制端，在不受输入信号影响的情况下允许或禁止器件工作有一个逻辑电源输入端，使内部逻辑电路部分在低电压下工作；可以外接检测电阻，将变化量反馈给控制电路。使用L298N芯片驱动电机，该芯片可以驱动一台两相步进电机或四相步进电机，也可以驱动两台直流电机。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. Main features are: high voltage, the maximum working voltage up to 46V output current, instantaneous peak current up to 3A, continuous operating current of 2A rated power of 25W. Contains two H-bridge high-voltage high-current full-bridge driver can be used to drive DC motors and stepper motors, relay coils and other inductive load using standard logic level signal control has two enable control terminal, input signal without affecting the case to permit or prohibit the device work a logic supply input, so that part of the internal logic circuits at low voltage work can be an external sense res

Modbus RTU Slave project based on Microchip PIC 16F87X processor and 24LC128 CMOS Serial EEPROM with I2C interface. PIC Modbus RTU slave supports write and read (3 and 16) functions. The data is stored and read from EEPROM via the I2C bus. You can write/read up to 8000 registers. In a single frame can be read/write 32 registers . The program was written in the HI-TECH C compiler-Modbus RTU Slave project based on Microchip PIC 16F87X processor and 24LC128 CMOS Serial EEPROM with I2C interface. PIC Modbus RTU slave supports write and read (3 and 16) functions. The data is stored and read from EEPROM via the I2C bus. You can write/read up to 8000 registers. In a single frame can be read/write 32 registers . The program was written in the HI-TECH C compiler

ads1211写寄存器，读数据，用C语言写成，稍微改动就可移植-ads1211 write register, read data, using C language written in a little change can be transplanted

利用actel公司的proasic3系列FPGA A3P030,VHDL编程,实现对LCD模块1602C的显示控制.已经调试通过.已经形成模版,可以进一步使用开发.-Actel companies use proasic3 series FPGA A3P030, VHDL programming, implementation of the LCD display control module 1602C.Has debugging. Has become the template, you can use to develop further.

程序出错提示代码-suggested procedure code errors

minigui的文档以及源代码和相关网页，有利于基于minigui的软键盘开发-minigui documents as well as the source code and related web pages, in favor of the soft keyboard based on the development of minigui

基于牛顿迭代法的二次规划程序，采用VC平台，适合解决大容量稀疏矩阵的优化问题-Newton iterative method based on the quadratic programming procedures using VC platform, suitable for solving large sparse matrix capacity optimization

SystemC片上系统设计源代码 希望对大家有帮助哈-System-on-Chip Design SystemC source code would like to have everyone help Kazakhstan

DS1302+162A+18b20+M8515做的温度时钟显示程序-temperature，clock display

高性能ISD2540-ISD251200芯片的运用-High-performance chip ISD2540-ISD251200 the use of