interruption in its DOS13 developed procedures graphics routines, classic exampl...

12位ADC芯片TLC2543的驱动程序，用于LPC2130系统中，模拟SPI总线（操作方便）-12-bit ADC chip TLC2543 driver for LPC2130 system, simulation SPI bus (easy)

适合linux初学者，介绍了linux相关特性和常用操作。-Linux for beginners, introduction of the linux-related features and used to operate.

Qt/Embedded是一个多平台的C++图形用户界面应用程序框架，其对象容易扩展，可移植性好，支持多个GUI平台的交互开发。现在，Qt/Embedded被广泛地应用于各种嵌入式产品和设备中。-Qt/Embedded is a multi-platform C++ graphical user interface application framework for easy expansion of the target, portability, and support multiple cross-platform GUI development. Now, Qt/Embedded has been widely used in a wide variety of embedded products and devices.

L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是：工作电压高，最高工作电压可达46V；输出电流大，瞬间峰值电流可达3A，持续工作电流为2A；额定功率25W。内含两个H桥的高电压大电流全桥式驱动器，可以用来驱动直流电动机和步进电动机、继电器线圈等感性负载；采用标准逻辑电平信号控制；具有两个使能控制端，在不受输入信号影响的情况下允许或禁止器件工作有一个逻辑电源输入端，使内部逻辑电路部分在低电压下工作；可以外接检测电阻，将变化量反馈给控制电路。使用L298N芯片驱动电机，该芯片可以驱动一台两相步进电机或四相步进电机，也可以驱动两台直流电机。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. Main features are: high voltage, the maximum working voltage up to 46V output current, instantaneous peak current up to 3A, continuous operating current of 2A rated power of 25W. Contains two H-bridge high-voltage high-current full-bridge driver can be used to drive DC motors and stepper motors, relay coils and other inductive load using standard logic level signal control has two enable control terminal, input signal without affecting the case to permit or prohibit the device work a logic supply input, so that part of the internal logic circuits at low voltage work can be an external sense res

旺宏Flash Memory MX29LV320 driver. This program can for embedded system that using MX29LV320 (4MBytes) flash memory. User can porting to any RTOS by himself.-Macronix Flash Memory MX29LV320 driver. This program can for embedded system that using MX29LV320 (4MBytes) flash memory. User can porting to any RTOS by himself.

MSP430的LCD驱动程序 [05-10-29] 74HC165驱动程序 [05-10-29] 74HC595驱动程序-MSP430 LCD driver [05-10-29] 74HC165 driver [05-10-29] Bit Drivers

/* ********************************************************************* *文件:codec.c *功能:声音的采集和回放 *编写:李存皓 *版本:1.0 *时间:2013/12/6 ********************************************************************* */ #include "init.c" #include /* ********************************************************************* *函数:main

资源描述该工程是市面流行红外触摸屏，支持四点触控，内包含了红外触摸屏多点识别算法，红外灯控制算法，USB-HID设备类开发，可以用来学习USB-HID设备类开发，同时内修改了4点标准触控报表。该工程所使用的MCU为市面是流行主流MCU-STM32，值得参考和学习。

在89C51芯片上运行，采用两个中断方式，一个外部0中断实现救护车通行，南北红灯10秒后恢复中断前状态，另一个是定时器0中断实现南北灯状态转换，16X16 LED点阵对应显示“南北”字样信息-89C51 chip in operation, interruption of the use of two methods to achieve an external 0 interrupt the passage of ambulances, the North-South red light 10 seconds after the resumption of state, and the other is the timer 0 interrupt to achieve the state of North-South light conversion, 16X16 LED dot-matrix corresponding show " South-North" in the information

应用背景 主要用于测试cypress的编程，实现USB的输入和输出端口的打通和通信 关键技术在cypress中实现的，将输入数据进行处理后直接通过输出端口进行输出，增加了命令处理的流程，只有合法的命令才能返回正确的数据，否则将返回出错数据。