用verilog读取陀螺仪数据并显示

企业用verilog代码风格规范 本规范规定了IC设计项目开发过程中VerilogHDL源代码的编写总则、要求及模板文件。(Enterprises with verilog code style guide for the preparation of this specification General IC design project development process VerilogHDL source code, requirements and template files.)

说明：  一维超混沌随机数的生成verilg，还有testbench仿真激励，modelsim的仿真工程。(The generation of one-dimensional hyperchaotic random number verilg, testbench simulation stimulation and Modelsim simulation engineering.)

可以实现从sd卡中读取数据，不依赖任何的ip核，简洁高效。

模块 ac_con (输出 heater_on、 cooler_on、 fan_on、 输入的 temp_low、 emp_high、 auto_temp、 manual_heat、 manual_cool、 manual_fan） ； 分配 heater_on = (temp_low & auto_temp) |manual_heat ； 分配 cooler_on = (temp_high & auto_temp) |manual_cool ； 分配 fan_on = (加热器上 | cooler_on | manual_fan; endmodule

说明：  ? 熟悉IIC协议总线协议，采用IIC总线对图像采集传感器寄存器进行配置，并转换为RGB565格式。 ? 利用异步FIFO完成从摄像头输出端到SDRAM 和SDRAM 到VGA 接口各跨时钟域信号的传输和处理。 ? 利用 SDRAM 接口模块的设计，实现了刷新、读写等操作；为提高SDRAM 的读写带宽，均采用突发连续读写数据方式；并采用乒乓操作实现 CMOS 摄像头与VGA的帧率匹配。 ? 利用双线性插值方法实现对图像640×480到1024×768的放大操作。 ? 完成VGA显示接口设计。(Familiar with IIC protocol bus protocol, IIC bus is used to configure the register of image acquisition sensor and convert it into RGB565 format. Asynchronous FIFO is used to transmit and process signals across clock domain from camera output to SDRAM and SDRAM to VGA interface. With the design of SDRAM interface module, refresh, read and write operations are realized. In order to improve the read and write bandwidth of SDRAM, burst continuous read and write data mode is adopted, and table tennis operation is used to achieve frame rate matching between CMOS camera and VGA. The bilinear interpolation method is used to enlarge the image from 640*480 to 1024*768. Complete the VGA display interface design.)

数字频率计，测量范围0-1GHZ,测周测频自动转换，精度极高，花了很长时间，不过还是有一点点小问题，有待改进.(Digital frequency meter, range 0-1GHZ, automatic conversion measured weekly frequency measurement, high precision, took a long time, but still a little small problems to be improved.)

LBM用于Poiseuille流初学者程序，直接反弹格式(LBM Poiseuille)

此程序是Verilog HDL语言读写RAM的程序希望大家有用(This is Verilog HDL Promang)

每次开机都将次数加1 并存储到EEPROM。这样就能直观的看到机器的使用次数 用P1口 LED做为显示，次数大于256是将溢出，按复位模拟开机 或者直接通过开关开机(Each boot will add a number of times and stored to the EEPROM. So you can visually see the frequency of use of the machine as with P1 port LED display, the number is greater than 256 will overflow, analog power or press the reset switch power directly through)

安富利SP605开发板ISE12.4版本的XBD文件，里面包括了开发板所有的接口，包括硬件和软件设计(Avnet SP605 development board ISE12.4 version XBD file, which includes the development board all interfaces, including hardware and software design)