这是一个接收单片机数据的软件,通过对接收的数据分析来显示相应的LED.目前只能显示一个LED,有时间会全部做好的,目前接收到的数据为0A0B0C,也就是从单片机...

ST-LINKII-KEIL 驱动 拷贝到keilarmin目录下 keil 3.22a以上版本-ST-LINKII-KEIL-driven copy to keilarm in directory keil 3.22a above

单片机与电脑一体机数据传送的接收部分.请多多支持-Single-chip machine and computer to receive data transmission part.

LED扫描驱动程序，是16分之一扫描，包含多种模式，闪烁时间可调。-LED Scan driver, is one of 16 sub-scanning, contains a variety of patterns, adjustable flashing time.

DDS芯片9851的驱动程序~用来产生不同频率的正弦波波形~-DDS chip driver 9851 ~ used to generate different frequencies of sinusoidal waveform ~

这是一个有实用价值的制作。可记录 0-17米每秒的风速。可靠性高、架设容易、适用范围广。可存放30.46天的数据，并可保存11个月。也就是说，在12个月内去抄一下数据即可。抄数据的方式是通过手提电脑的串行口。供电方式为太阳能电池及普通电池。-This is a practical value has produced. Record of 0-17 meters per second wind. High reliability, easy to set up, the application scope. 30.46 days to deposit the data, as well as preservation of 11 months. In other words, in the 12 months to what data can be copied. Copied data is through the serial port of portable computers. Power supply for solar cells and normal cells.

用IAR编写，MSP430中I2C总线的应用-IAR prepared to use, MSP430 in the application of I2C bus

PIC单片机的1602液晶显示，包括8位数据控制和4位数据控制-PIC MCU 1602 liquid crystal display, including the 8-bit data control and 4-bit data control

pic单片机中时钟芯片1302的应用 此文件已经过实际应用-pic microcontroller in the application of clock chip 1302 has been the practical application of this document

nR24L01_EVB开发板试验接口初始化及模块读写程序-nR24L01_EVB development board initialization and test interface module to read and write procedures

红外线遥控器按键检测程序. 通过检测两次下降沿之间的时间差判断接受到的数据位. 已经通过了测试,能够正确区分出32bit数据的遥控器按键键值. 具有数据重发功能,但是数据的重发有点频繁. 使用晶震频率为11.0592MHz,所有定时值都是基于这个频率计算. 占用很少量的CPU时间,使用了外部中断0接受数据,定时器0进行计数, 定时器1作为串口的波特率发生器(Band = 9600).-Infra-red remote control button detection program. By detecting falling edge twice to determine the time difference between the received data bit. Has passed the test, could correctly distinguish 32bit data button remote control key. With data re-issued, but data a bit of re-issued frequent. Zhenyuan frequency of use of crystal 11.0592MHz, all timing values are calculated based on this frequency. occupied by small quantities of CPU time, use the external interrupt 0 to accept data, timer 0 to count, timer 1 as a string port baud rate generator (Band = 9600).