基2_8点fft运算的verilog代码

Use this multimeter to make precise electronic measurements and tests. Easy-to-read LCD readout, positive set selector switch and 32" leads. AC voltage

CS5460校准程序，控制器为C8051F310，SPI通信协议，可以作为电表芯片示例(CS5460 calibration procedure, the controller for the C8051F310, SPI communication protocol, as the meter chip sample)

时间同步后即可确定每帧数据的起始位置，这样就能完整的截取下每一帧。但是，数据中还带有频偏信息。在常规的通信系统中，多普勒很小仅仅会带来很小的频偏，但是在大多普勒的情况下，频偏将非常大，20马赫的速度将会带来将近34K的频偏。因此，如何很好的纠正频偏即为本系统的难点。 OFDM中，我们将大于子载波间隔倍数的频偏称为整数倍频偏，而将小于一个子载波间隔的频偏称为小数倍频偏。频偏矫正精度只要能保证小于十分之一倍的子载波间隔，频偏就不会对均衡和解调造成影响。本文中我们借鉴这种思想，由于硬件资源限制，我们将在接收端做64点FFT，即相当于将频域划分为64份，我们将小于 的频偏称为小数倍频偏，将 整数倍的频偏称为整数倍频偏。本程序即基于SCHIMDL经典方法完成小数倍频偏纠正(After time synchronization can determine the starting position of each frame data, so you can complete the interception of each frame. However, in the data with frequency information. In conventional communication systems, doppler small will bring only small deviation, but in the case of most of the doppler, frequency PianJiang is very large, 20 Mach speed will lead to deviation of nearly 34 k. Therefore, how to good to correct deviation is the difficulty of this system. OFDM, we will be bigger than the sub-carrier spacing ratio of frequency deviation is called the integer frequency offset, and the interval will be less than a child carrier frequency offset is called decimal frequency doubling. Deviation is less than one over ten times as long as can guarantee accuracy of sub-carrier spacing, deviation will not affect balance and demodulation. This article, we draw lessons from the idea, due to the limited hardware resources, we will do 64 points FFT at the receiving end, which is equ)

DSP28335与FPGA通过spi通信，此程序为28335为主接收程序(DSP28335 and FPGA through the SPI communication, this procedure for the 28335 receiving procedures)

该文件是booth乘法器的verilog源代码，经过最终的仿真，可以直接运行(This file is booth multiplier verilog code, after the final simulation, can be directly run)

1、用状态机设计A/D转换器ADC0809的采样控制电路，并在数码管上显示转换结果； 2、设置有复位和启动/保持开关，要求 ⑴ 复位开关用来使A/D转换器复位，并做好A/D转换准备； ⑵ 启动/保持开关用来控制A/D转换器开始连续转换或停止转换保持结果，即按一下启动/保持开关，启动A/D转换器开始转换，再按一下启/停开关，停止转换并保持结果。 3、采用Verilog HDL语言设计符合上述功能要求的控制电路。(1, with the state machine design A/D converter ADC0809 sampling control circuit and display the results on the digital conversion 2 is provided with a reset and start/hold switch, reset switch is used to make the request ⑴ A/D converter reset and do A/D conversion ready ⑵ start/hold switch is used to control the A/D converter starts converting or stop the conversion to maintain a continuous result that by clicking Start/hold switch, start the A/D converter to start the conversion, and then Click the start/stop switch stops the conversion and keep the results. 3, using Verilog HDL language designed to meet the functional requirements of the above-mentioned control circuit.)

基于图像处理的中值滤波VHDL源码,能够实现对图像的滤波(Based on the median filter VHDL source image processing, image filtering can be achieved)

初学学习verilog的经验，可以帮助新手以正确的思维方式，学习方法学习。(Verilog learning experience)

将VHDL程序下载到DE2开发板，引脚分配时需要知道的芯片每个引脚功能(VHDL program will be downloaded to the DE2 development board, you need to know when the pin assignments for each pin of the chip functions)

使用verilog语言设计的512位RSA加密处理器代码，保护测试模块。 设计的代码简单易懂，适合学习FPGA的新手查阅。 代码已经经过FPGA板上测试通过，保证可以运行。