Series Singlechip c8051f06x procedures, including the header files and ad some c...

LCD1602液晶显示器的驱动程序,是用AVR的M16L来驱动的.-LCD1602 LCD driver, is to use the AVR to drive the M16L.

另外一个RC531非接触式读卡器的全部源代码，实现全部功能-another RC531 non-contact reader the full source code, to achieve full functionality

单片机80C522，里面有实用的程序源吗码-80C522 microcontroller, there are practical program source code?

单片机为控制器件的，一个小巧的频率测试器。用c语言编写，用过验证和实际实践。-microcontroller for the control device, a compact frequency device. C language with the preparation, certification and used actual practice.

主要用于液晶电视解码,内置51单片机,全部代码用C编写,编译环境为KEILC-Mainly used for LCD TV decoder, built 51 single-chip, all of the code prepared by C, the compiler environment KEILC

用8051驱动240*128液晶的C51程序，控制器为T6963，由于代码比较大，试验时请用52 本程序移植性较好，已成功移植到MSP430上-8051 with 240* 128 LCD drive the C51 procedure, the controller for the T6963, as a result of relatively large code, test when you use 52 transplant procedures better, have been successfully transplanted into MSP430 on

16位计数及激光测距仪的源程序,C源代码,对学习有很好的参考价值.-16 counts and laser rangefinders of the source, C source code, to learn a good reference value.

步近电机控制代码，可以控制正反，停，限位等功能，带仿真图。-Near step-by-step motor control code to control both positive and negative, stop, limit and other functions, with simulation of Fig.

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

在lpc2114 上的ADS例子，是学习GUI 的好例子，上面还附带有protues仿真的工程-ADS in the lpc2114 example is a good example of learning GUI, the above also comes with protues simulation project