用at89s52访问MAX7219(LED数码显示）

自己写的小程序，关于世界时钟的 有兴趣的同学可以看一下

8051 VARIOUS UTILITY FUNCTIONSUTIL_ADCAD - Add Acc to DPTR, sets CYUTIL_ADCBAD - Add B/A to DPTR, sets CYUTIL_SUBBAD-8051 VARIOUS UTILITY FUNCTIONSUTIL_ADCAD- Add Acc to DPTR, sets CYUTIL_ADCBAD- Add B/A to DPTR, sets CYUTIL_SUBBAD

Discription: This multi-master driver provides the software interface to the I2C Bus hardware of the M3062x series of MitsubishiMCU.

usb-isp,直接用usb对avr单片机编程,简单易用-usb-isp, the direct use of usb for avr Microcontroller Programmer, easy-to-use

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

模数转换，即ad-convert,能够实现模拟到数字的转换。-ad-convert

适合于PIC单片机的TCP/IP协议栈-suited to the PIC TCP/IP Protocol Stack

单片机叮咚门铃，52单片机示例，程序简单，适合初学者下载-SCM ding-dong doorbell

=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器－－被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi